From figure below, , if 3 phase bolted fault occurs at point 2. Calculate i) Rating of CB's ii) Volt at point 1 iii) Generator terminal Data are as follows: Gl: 100 MVA, 22 Kv,Xgi" = 0.2 pu G2: 100 MVA, 22 KV, X,2"=0.15 pu TR1: 100 MVA, 22/220 KV, XTRI =0.1 pu TR2: 100 MVA, 22/220 KV, XTR2=0.1 pu

From figure below, , if 3 phase bolted fault occurs at point 2. Calculate i) Rating of CB's ii) Volt at point 1 iii) Generator terminal Data are as follows: Gl: 100 MVA, 22 Kv,Xgi" = 0.2 pu G2: 100 MVA, 22 KV, X,2"=0.15 pu TR1: 100 MVA, 22/220 KV, XTRI =0.1 pu TR2: 100 MVA, 22/220 KV, XTR2=0.1 pu

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: fault location

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault Three phase…

Q: Equipment ratings and per-unit reactances for the system shown in the below figure are given as…

Q: Problem 5 Consider the system shown in the single-line diagram of Figure (3). All reactances are…

A: Single Line Diagram: A single-line diagram, often known as an SLD, is an electrical diagram or…

Q: A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the…

A: x=1y=7Note: reactance of element right to bus 4 is not given. Hence we will not consider that in…

Q: pecified in per unit. For generators, assume Z* =Z` =j0.2, Z° = j0.05 For transformers, assume Z' =…

Q: Three zones of a single-phase circuit are identified shown in Figure below. The zones are connected…

Q: G1 Bus 1 Bus 2 Line Bus 3 T2 Bus4 M1 j402 25 MVA Ye A 13.0 kV Xg1 =10% зо мVA 13.4/69 kV 20 MVA…

Q: A 25 MVA, II kV generator has X"d=0.2 p.u. X2 = 0.3p.u. and X0=0.1 p.u. Tht neutral of generator is…

Q: Three single-phase two-winding transformers,

Q: b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

Q: Symmetrical Fault Analysis Q.13 Topic Power Systems - Symmetrical Fault An... A 100MVA, 33KV…

A: Given- 100 MVA, 33 KV generator- Reactance =0.25 p.u., 0.45 p.u., & 0.05 p.u., To Find- The…

Q: The one line diagram of a simple 3-bus power system shown below. All impedances are expresses in per…

A: According to the question, we need to calculate the fault occurred on bus 3 is a three phase fault.

Q: Problem #2: A transformer is fed from a 100 MVA, 18 kV generator via a 5-cycle breaker. Generator…

A: Given S =100 MVA V =18 KV Xd'' =18%Xd' =25%Xd =120%

Q: The plant capacity of a three phase generating station consists of two 15,000 kVA generators of…

Q: Q.3 When a line-to-ground fault occurs, the current in faulted phase 'a' is 100A. The zero-sequence…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

100%

From figure below, , if 3 phase bolted fault occurs at point 2. Calculate
i)
Rating of CB's
ii)
Volt at point 1
iii)
Generator terminal
Data are as follows:
Gl: 100 MVA, 22 Kv,Xgi" = 0.2 pu
G2: 100 MVA, 22 KV, X,2"=0.15 pu
TR1: 100 MVA, 22/220 KV, XTRI =0.1 pu
TR2: 100 MVA, 22/220 KV, XTR2 =0.1 pu
TR1
ZTL-J50 ohm
св
TR2
св
G2
fault
Zload =(0.2 + j0.1) pu

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The one-line diagram of a power system is shown in the figure below. A single-line-to- ground (SLG) fault occurs at bus 2. Assume the fault impedance Z,= j0.08 pu. Calculate the fault current (in per unit). T, 2 M Line X, = X2 = 40 N Xo =1200 %3D 100 MVA 13.8 kV 100 MVA 100 MVA X, = 0.15 13.8-kVA/138-kVY X = 0.10 per unit 138-kV Y/13.8-kV A 100 MVA X2 = 0.17 X = 0.10 per unit 13.8 kV X, = 0.20 X2 = 0.21 Xo = 0.10 X, = 0.05 per unit Xo = 0.05 per unit
A three-phase, 100-MVA, 20-kV generator is connected to a three-phase, 100-MVA, 20-kV motor through a transmission line. The reactances of the generator and motor are 0.25 and 0.20 per unit, respectively. The line reactance is 0.10 per unit. The motor is taking 50 [MW] at 0.8 power factor leading at rated voltage. Suppose a three-phase short circuit occurs at the generator terminals, determine the transient currents in the generator and motor as well as the short-circuit current.
2A. What is another term for "shunt"? a) in series b) in parallel c) compounded d) none of the above 2B. Which of the following is/are a basic type of DC generator connection? a) series b) shunt c) compound d) all of the above
8
The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current through the neutral during the fault is j0.8 True False
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
Q2\ The one-line diagram of a simple power system is shown in figure below. All impedances are expressed in per unit (pu) on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = j0.08 per unit. Using Thevenin's theorem obtain the impedance to the point of fault and the fault current in per unit. Determine the bus voltages and line currents of generators during fault. X₁ = = 0.1 XT-0.1 3 1 to ojo XL=0.2 2 040 X₁ = 0.1
Please solve d, e, f ONLY.
Q3/ For the system shown in figure. The generator is supplying 1.0 pu MW power under prefault condition. When three-phase fault occur at point F. What should the value of fault reactance must be to make the critical clearing angle equal to 58.9. Sc j0.1 j0.1 10.21 BE j0.38 38 j0.21 IEgl-12 pu 10.19 F 10.19 IVI-1.00 pu j0.1 j0.1 Q4/ Figure below shows the one-line diagram
Help me with this, I really need it
A 10,000 KVA, 13.8 KV turbo-generator having x-x,-15% and x-5% is about to be connected to a power system. The generator has a current limiting reactor of 0.7 ohm in the neutral. Before the generator is connected to its system, its voltage is adjusted to 13.2 KV when a double line to ground fault develops at terminals band c. Find the initial symmetrical current in the ground and in the line. Ans: I, 2800 A; I=3090 A