For the vertical flexural member shown, determine the maximum compressive stress in MPa at section K, as shown on figure a-777 mm; b=364 mm; c=75 mm; d 70 mm; F₁-408 N, F₂-4720 N; F₂=1198 N. d C X Cross-sectional view at section K. F₁ F₂ b F₁

For the vertical flexural member shown, determine the maximum compressive stress in MPa at section K, as shown on figure a-777 mm; b=364 mm; c=75 mm; d 70 mm; F₁-408 N, F₂-4720 N; F₂=1198 N. d C X Cross-sectional view at section K. F₁ F₂ b F₁

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
Figure below shows the bar with three equal elements. Use the finite element method and calculate: 2.1 the global stiffness matrix 2.2 the displacement on node 2, 3, 4 2.3 the Strain in each element 2.4 the stresses in each element using Hook's law and compare with theoretical stresses (o=F/A) (1) (2) (3) -50 N 10 mm 10 mm 10 mm A1=50 mm? A2=20 mm? A:=10 mm? E=200 GPa
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
please box in the following answers: normal stresses for beam AB and BC (mid section) normal stresses for beam AB and BC (at connections A and C) shear stress for pin A, B and C bearing stress along member AB and BC at pin section for A and C 600mm Flat end 40 mm FRONT VIEW d-25 mm d-25 mm 50 mm 125 mm 30 mm 25mm ,20 mm TOP VIEW OF ROD BC -800 mm Q-30 kN TOP VIEW OF BOOM AB d=25mm Flat end Q-30KN 20mm 20 mm END VIEW 600 mm 50 mm 20 mm 800 mm 30 AN 1
Try One scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN, determine the force components perpendicular (N) and parallel (V) to a – a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a – a. 90 mm 62° a N kN kN Aa-a mm2 P = 80 kN MPa MPа Try one 1st 2nd 3rd Enter attempt
For the flat stress state shown in the figure. Use Mohr's circle to determine (show the procedure only with the use of geometry): a. Draw Mohr's circle indicating coordinates of the points that represent the given stress state, center, radius, coordinates of the points that represent the state the maximum and minimum normal stresses, coordinates of the maximum shear and angle of rotation from the stress given to the plane principal. b. Use the results of literal a to draw the element subjected to main forces and the element subjected to maximum shear. 12 MPa 19 MPа y 19 MPа 46 MPа 46 MPа 19 MPа 19 MPа 12 MPa
A cast iron link has dimension of 40 x 200 x 500 mm as shown in the figure. The compressive load P = 400 kN is applied to the ends of the link along a longitudinal axis that is located 150 mm above the bottom of the link (50 mm above the neutral axis). Determine the normal stress developed at the bottom surface point A. 50 mm NA- 150 mm 200 mm A 500 mm 40 mm
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
The state of stresses at a point of a structure is shown in the figure below.A- find the principal stresses (show the results in a correctly oriented sketch).B- find the maximum shear stress with its average stress (show the results in a correctly oriented sketch).
Q-1 Figure Q-1, below, shows Mohr’s circle for a point in a physical object that is subjected to plane stress. Determine the stresses σx, σy, and τxy, and show them on a stress element, properly oriented with reference to x-y axes. Determine the principal stresses σ1, σ2, and τmax and show them on a stress element properly rotated with respect to the x–y element Determine the stresses σn, σt, and τnt, and show them on a stress element that is properly rotated with respect to the x–y The sketches must include the magnitude of the angles w.r.t. positive x-axis as well as the angle between the x and n axes, and an indication of the direction of rotations (i.e., either clockwise (c.w.) or counterclockwise (c.c.w.)).
The state of stress at a point in a structure is shown in the following figure.(a) find the main stresses (Show the results on a sketch ofcorrectly oriented).(b) Find the maximum shear stress with its average stress (Show theresults in a correctly oriented sketch).