The assembly shown consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A =7 mm, between the lower end of the steel rod and its pin support at C. The stress in the aluminum rod (in MPa) when the lower end of the steel rod is attached to its support is: Eal 70 GPa, Est 200 GPa. A= 240 mm2, As= 170 mm2. %3! 0.75 m 1.5 m

The assembly shown consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A =7 mm, between the lower end of the steel rod and its pin support at C. The stress in the aluminum rod (in MPa) when the lower end of the steel rod is attached to its support is: Eal 70 GPa, Est 200 GPa. A= 240 mm2, As= 170 mm2. %3! 0.75 m 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

مقاومة المواد
The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast 1000 mm2 Est 200 Gpa) and one post BE made of aluminum (AAI = 1500 mm2, EAI = 73.1 Gpa). If a central load of (400+b) kN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.1 mm between post AD and post CF with the rigid member ABC. 400 kN -0.5 m- -0.5 m A B 0.4 m F
I need it in 5 minutes please Diameter=38 Length=0.8
Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .If the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 B 36N/M 2m 1m pin sapport 1m 2m 3GN/M
The rectangular piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 16.4 MPa for compression. Round off the final answer to three decimal places.
(1) Given: B P=28 KN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm (3) Q R = 38 kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If an axial load of F= 300 N and the cross sectional area of the rod is 200 mm² , determine the stress in the section of copper. ... Copper Steel 2F F 3m 2m (A) 4.5 MPa (B 0.75 MPa C) 3.0 MPa D) 1.5 MPa
Please read the instructions carefully and do what are asks. Illustrate and show the COMPLETE SOLUTIONS. FN=70 MN=76 SN=50
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
3) At room temperature (20 °C) a 0.8 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 120 °C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod Bronze: Aluminum: Steel: Area: 1000 mm2 Area: 2000 mm2 Area: 1500 mm2 a = 18.4 x 10-6 E = 103 GPa a = 23.6x 10-6 E = 75 GPa a = 17.3 x 10-6 E = 190 GPa %3D %3D 0.8 mm 100 mm 150 mm 300 mm Bronze Al Steel
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a stress equivalent to your SN and MN in kips respectively, determine the maximum weight of that body. Neglect the weight of wood and cable. Note: Round off your answer in two decimal places. ... Cable (A = 0.5 in 2) 9 ft C B 12 ft Weight A Wood Strut ( A 16 in 2)