For the flat stress state shown in the figure.Use Mohr's circle to determine (show theprocedure only with the use of geometry):a. Draw Mohr's circle indicating coordinates ofthe points that represent the given stressstate, center, radius, coordinates of the pointsthatrepresent the state the maximum andminimum normal stresses, coordinates of themaximum shear and angle of rotation fromthe stress given to the plane principal.b. Use the results of literal a to draw theelement subjected to main forces and theelement subjected to maximum shear.12 MPa19 MPаy19 MPа46 MPа46 MPа19 MPа19 MPа12 MPa

Answered: Image /qna-images/answer/dca7b1a5-e2bc-4c19-b992-8dc9c918a957.jpg

Answered: For the flat stress state shown in the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please work out part A and B
Q: The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD" ; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circle] 2 kN/m² 6 kN/m² + + B D 2 kN/m² 2 kN/m²
What modulus of elasticity in tension is required to obtain a unit deformation of 0.00105 m/m from a load producing a unit tensile stress of 44,000 psi? A. 42,300 x 10⁶ psi B. 41,202 x 10⁶ psi C. 43,101 x 10⁶ psi D. 41,905 x 10⁶ psi Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
Please do it for me as soon as possible. Do not worry about typing it. Hand writing is enough.
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
The state of stress at a point on an element of material is shown. Let sigmaX= 49.0 ksi, sigmaY= 17.0 ksi, and Txy= 11.0 ksi. Use this information to represent the principle state of stress and maximum in plane shear stress. Plot the mohr circle and state sigmaX' and sigmaY' and Tx'y' with unit. Also draw the state of stress on the rotated element.
A shaft is subjected to a torque of 28 kNm and a maximum bending moment of 25 kNm. The shaft is solid with a diameter of 125 mm. Using the Mohr circle method find the values for the principal stresses and themaximum shear stresses on the shaft i)Construct the Mohr circle on the graph paper provided. ii) Using the Mohr circle method find the values for the principal stresses and the maximum shear stresses on the shaft.iii) Show the orientations of the planes on which the principal stresses act on a rotatedelement
why the expert here wrote -200 cos 75 when Σ Fx = 0 , I understand all steps but how he got - 200 cos 75 ( for the force ) (how the angle is 75 ) can you please clarify for me this point please ...... because I did not got the angle 75 dgree for 200 N force can you draw a diagrm for me please to see how 75 dgree links to 200 N
For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear stress acting at the point by using equations, then show these stresses on an appropriate sketch. 2- The normal stresses 0 n and ¢ t and the shear stress T nt for element oriented 20° clockwise from the position shown, using Mobhr’s Circle. 75 MPa
For the stress state: Oz = 30 ksi, oy = 40 ksi, Try = -10 ksi a. Find the principal stresses and draw the stress element in the principal orientation. b. Find the maximum in plane shear stress and draw the stress element in the maximum in plane shear orientation.
The element in the image has a horizontal force of 20 N and a vertical force of 25 N. The element was made of a 25.4 mm diameter steel bar. Determine:to. The four states of stress from the farthest place of the forces and obtain the critical point.b. For the critical point, construct the Mohr circle.C. Obtain the maximum principal and normal shear stresses for the critical point.d. The angles at which the maximum normal and shear stresses occur.and. Draw the rotated tension state for the angles obtained and with the corresponding tensions.
1) Determine the normal force at point C(Nc) Express your answer in pounds to three significant figures 2) Determine the shear force at point C(Vc) . Express your answer in pounds to three significant figures. 3) Determine the moment at point C.(Mc) Express your answer in pound-feet to three significant figures.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS