The maximum in-plane shear stress occurs on a plane that is 45° away from the principal planes. The average normal stress on this The state of stress at a point can be described by Jo| = 30 MPa , |o,| = 72 MPa , and |Tzy| = 17 MPa , acting in the directions shown (Figure 1). plane is generally not zero, but is avg = 2 The maximum shear stress is given by the following equation: Part A - In-plane shear stress 2 Tmax = +T, What is the maximum in-plane shear stress for the given state of stress? Express your answer with appropriate units to three significant figures. Once oayr and Tmax are calculated, the principal stresses can be found very directly: 01,2 = oavg + Tmax • View Available Hint(s) Tmax in-plane = 27.0 MPa igure 1 of 1> Submit Previous Answers y Correct Oy Part B - Maximum normal stress magnitude What is the principal normal stress with the largest magnitude? Express your answer with appropriate units to three significant figures. • View Available Hint(s) Txy HẢ ?

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: need help with part b i solved a prior

A: ◆ The mean effective pressure: 562.94 kPa. ◆ The indicated power developed by the engine is 4.10 kW.…

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: What process does this following sample have gone through? I. none II. quenching III. annealing IV.…

A: ALL THE OPTION ARE HEAT TREATMENT PROCESS LIKE ANNEALLING ,QUENCHING AND COLD ROLLING .

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: 1. Explain how Jominy test results can be used to validate a particular steel grade for a specific…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: what happened with the 10 in the first equation?

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: d W Pm a Ps

A: The free body diagram of the system is showing below –

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: what is the bottom length?

A: To calculate the bottom length

Q: Help!!! Answer all correctly! Please

A: Step 1: The answer is: Option A, B, C, and D are all correct. Step 2:Explanation: In each case, the…

Q: How were the areas for part 2 found?

A: Given Data and to find: How the areas are calculated?

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: One kmol of ethane (C₂H6) is burned with an unknown amount of air during a combustion process. An…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.