For the circuit below, Assume constant-voltage model VD,on =800 mV and VB=1.4 V. In this circuit, Vin is increased from 0 to a finite value. At what value of Vin, does D1 starts to conduct? What is the current of resistor R1= 2kΩ, if Vin=5 V? What is the output voltage, Vout, if Vin=5 V? What is the voltage across R1 if Vin = 5 V? What is the current of resistor R1= 2kΩ, if Vin=1.8 V? What is the output voltage, Vout, if Vin=1.8 V?

Q: For the circuit below with input voltage V1 shown and the initial voltage across Cl equal zero, find…

A: In this question,  Find the voltage across the capacitor if initial voltage across the capacitor is…

Q: Sketch the output voltage for each Zener limiting circuit in the Figure for the following cases: a)…

A:

Q: Consider the circuit in Figure A2 where Vs = 12 V, R₁= R₂ and the input is a sinusoidal signal with…

A:

Q: 3.87Kohm, R1 = 5475.00Kohm, R2 = 6525.00Kohm, R3 = 1.90Kohm, R4 = 0.63Kohm, R5 = 22.19ohm, Ry =…

A:

Q: Exercise 2: Buck Converter Design: Design a buck converter to produce an output voltage of Vo=18 V…

A: It is asked to design a buck converter for the given values of input and output voltages. We need to…

Q: Refer to the circuit in Figure Q2. Sketch and label the input voltage, Vi and output voltage, Vo. Vi…

A: In this question We need to determine the input and output waveform.  We know Vo /Vi = -100

Q: Refer to the following figure. If BDC = 100 and VCE(sat) = 0.1 V , the value of IC(sat) is equal to…

A: By kvl Vcc-Ic(sat) × Rc - Vce(sat)=0 So Ic(sat)= (vcc - Vce(sat))/Rc

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re LOKO RB Vcc Bpc = 50 www 20…

A:

Q: 2. The circuit below is a emitter follower (the output is taken from the emitter and its voltage…

A: This question belong to small signal modelling of transister and it is in common collector…

Q: 3. Assume the input to the circuit below is given by 3sin(2лft) Volts, where f-1000 Hz. What does…

A:

Q: Draw and label a voltage divider that generates0.5V from an input of 1.5V. Then draw and label a…

A: PRESENCE OF SOURCE: In the presence of sources all the passive elements which are R, L and C always…

Q: Consider the circuit in Figure A2 where Vs = 12 V, R₁ R₂ and the input is a sinusoidal signal with…

A:

Q: 5, P-P sine @ 1kHz € 2K M IKS ww TOK Vo

A: 5) To find the output voltage of the given op-amp circuit

Q: write the way to find CMRR with all details and needed comprent Notes G₂ you have to draw the…

A: The Common - Mode Rejection Ratio is abbreviated as CMRR.  The CMRR of an op-amp is used to identify…

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.