Five different particle sizes are mixed in proportions shown below and water is added to make the volume of soil suspension exactly equal to 1000 cc. Particle size, mm Weight, g 0.060 0.020 0.010 0.005 0.001 5 15 20 4 6 The particles have a specific gravity of 2.65 and the dynamic viscosity of water is 8.95 millipoises. Y can be taken as 1.0 g/cc. The soil suspension was thoroughly shaken and sedimentation allowed. What is the largest particle size present at a depth of 10 cm after 8 minutes of the start of sedimentation? What is the specific gravity of the soil suspension at a depth of 10cm after 8 minutes of the start of sedimentation?

Five different particle sizes are mixed in proportions shown below and water is added to make the volume of soil suspension exactly equal to 1000 cc. Particle size, mm Weight, g 0.060 0.020 0.010 0.005 0.001 5 15 20 4 6 The particles have a specific gravity of 2.65 and the dynamic viscosity of water is 8.95 millipoises. Y can be taken as 1.0 g/cc. The soil suspension was thoroughly shaken and sedimentation allowed. What is the largest particle size present at a depth of 10 cm after 8 minutes of the start of sedimentation? What is the specific gravity of the soil suspension at a depth of 10cm after 8 minutes of the start of sedimentation?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The results of a laboratory proctor test are shown below: No.of Test 2 3 4 Wt.of Mould & Soil (Kg) Water content (%) 3.526 3.711 3.797 3.906 3.924 3.882 8.33 10.40 12.23 16.20 17.92 20.39 The mould is 12.7 cm. high and has an internal diameter of 10 cm., The weight of the Empty mould is 1.89 kg. 1) Plot the moisture content vs. dry density curve and determine the optimum moisture content and the max dry density. %3D (1) Plot the zero air content curve and 10% air content curve. Given G = 2.68.
Coarse aggregate is placed in a rigid bucket and compacted with a tamping rod to determineits unit weight. The following data are obtained:• Volume of bucket = 0.5 ft3• Weight of empty bucket = 20.3 lb• Weight of bucket filled with dry compacted coarse aggregate = 76.8 lba) Calculate the dry-compacted unit weight of the aggregate.b) If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids.
The properties of seven different clayey soils are shown below. Investigate the relationship between the strength and plasticity characteristics by performing the following tasks: Soil Beauharnois Detroit I Horten Gosport Mexico City Shellhaven St. Thuribe Mineral % Clay fraction (<2 μm) Kaolinite Illite 79 36 40 55 90 41 36 Montmorillonite Halloysite (hydrated) Halloysite (dehydrated) Attapulgite Allophane Activity, A 0.52 0.36 0.42 0.89 4.5 1.33 0.33 Liquid limit, LL 35-100 60-120 100-900 Undisturbed shear strength (kN/m²) 50-70 40-55 150-250 200-250 18 17 41 29 46 36 38 a. Estimate the plasticity index for each soil using Skempton's definition of activity. b. Estimate the probable mineral composition of the clay soils based on plasticity index and activity using the table below. Plastic limit, PL 20-40 35-60 50-100 Sensitivity, S, 14 40-60 30-45 100-125 120-150 2.5 17 2.2 5.3 7.6 150 Activity, A 0.3-0.5 0.5-1.2 1.5-7.0 0.1-0.2 0.4-0.6 0.4-1.3 0.4-1.3 c. Sensitivity refers to the…
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket =14L Weight of empty bucket = 9.21kg Weight of bucket filled with dry rodded coarse aggregate: Trial 1 =34,75 kg Trial 2 =34.06 kg Trial 3 =35.74 kg a. Calculate the average dry-rodded unit weight b.If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
Sieve analysis of a sample of fine aggregate resulted in the following data No. Sieve number 4 8 16 30 50 100 Sieve opening (mm) 4.75 2.36 1.18 0.6 0.3 0.15 Weight retained (g) 13 75 120 126 105 61 A) The total weight of the sample, assuming no mass loss during the analysis, is______ (g) a) 505; b) 500; c) 550 B) The half sieve used in the experiment is________. a) No.8; b) No.50; c) none of the above C) The fineness modulus of the aggregate________. a) 6.13; b) 3.16; c) 1.36 D) The average size of the aggregate___________. a) No.30; b) No.4; c) No.16
Three samples of fine aggregate were taken from the same stockpile and have the properties shown below. Determine in percentage: (a) total moisture content of each sample, (b) free moisture content of each sample, and (c) the average values of each from the stockpile. Measure Wet Mass (g) Dry Mass (g) Absorption (%) A 521.0 491.6 2.5 Sample B 522.4 491.7 2.4 C 523.4 492.1 2.3
The following data of a particular asphalt concrete mixture. Compute the percentage of voids in the laboratory molded specimen. Materials Specific Gravity Percent by weight Limestone Dust 2.80 |17.0 Sand 2.60 73.0 Asphalt Cement 1.02 10.0 A cylindrical specimen of the mixture was molded in the laboratory and weighted in air and water as follows.l Weight of dry specimen in air = 110 grams Weight of saturated surface - dry specimen in air = 114 grams Weight of saturated specimen in water = 60 grams 13.57% O 11.69% O 18.96% O 10.53%
Fine aggregate sample was tested to find its physical properties. The test results were as follows: Bulk specific gravity= 2.45, Apparent specific gravity= 2.5, mass of the vessel full of water = 1300 gm, mass of the vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm. Calculate 1- absorption% 2- moisture content% 3- Bulk density 4- Apparent density
determine the effective specific gravity of aggregates. DATA: Specific Gravity: Fine Agg = 2.603 Coarse Agg = 2.740 Asphalt Cement = 1.048 Percent By Weight: Fine Agg = 47.90 Coarse Agg= 47.78 Asphalt Cement= 100-FA-CA
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? " Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.18 0.15 (No. 0.075 Pan mm (in) (3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80) 100) (No. 200)| Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Datained.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?