Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [ 9:57

Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [ 9:57

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of 0.1 in. The bar is not rotating. The bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 25 000 lbf in. The bar is hot-rolled AISI 1095, but the groove has been machined. Determine the factor of safety for fatigue based on infinite life and the factor of safety for yielding. Plars & .
4. The shaft that is pictured is to be loaded by a purely reversing load, cycling at ± 500 lbf. The shaft is to be machined, operate in an environment at 100°C, have a reliability of 90%, and be made of a material in which Sut= 80 kpsi and Sy = 65 kpsi. The stress concentrations at A are K₁ = 1.6 for bending and Kt = 2.0 for torsion. Assume the notch sensitivity factor for torsion and bending to be 1.0. 10 inches a. Using the information provided with the attached log-log scale, create an S-N diagram assuming a steel shaft subjected to only bending. Estimate how many cycles of life can be expected if the alternating stress is 60 kpsi. F = ± 500 lbf b. would the S-N diagram from part (a) be different if only torsion were experienced (no bending)? Briefly explain why. c. ( Using a factor of safety of 2.0 based on infinite life, determine the minimum allowable diameter for shaft AB using the modified-Goodman criterion. B 8 inches
A solid 11 mm diameter shaft is subjected to an axial load of P- 33 kN and a torque of Tacting as shown. If the largest shear stress in the shaft must be limited to 201 MPa, what is the largest torque Tthat can be applied to the shaft? (1) Part 1 Calculate the cross-sectional area and the polar moment of inertia for the shaft. Answer: A = mm2 J= mm4
A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of 2200 Nm with a safety factor against yielding of 3. If the steel has a yield stress of 250 MPa, find the minimum permissible diameter for the shaft. Use von Mises’ theory of yielding.
Figure shows a cantilever shaft made of steel subjected to several loadingT=5kNm, M=2.5kNm, and P=120kN. If the diameter of the shaft is 60mm, and the yield stress is 310MPa, calculate the safety of factor of the shaft using the Von Mises yield criterion.
Please design the following mechanical shaft targeting design objective of reliable structure and performance via design iterations with constrains of geometrical dimensions within performance requirement, safety, and economic factors (finding minimum material cost of suitable diameter). Notes: This shaft is transmitting 200 kW at 1200RPM. Please design the shaft with a suitable diameter via iterations, if the maximum torque transmitted exceeds the mean by 30%. Take maximum allowable shear stress as 70 MPa.
The shaft shown in the figure is machined from AISI 1030 CD steel. The shaft rotates at a constant RPM and is supported by roller bearings at A and B. The profile keyway at F has static stress concentration factor of Ktb = 2.312 for bending. The applied forces at gears C, D and F are in the same plane as the bearing reactions and remain constant. a) b) Clearly draw and label shear and bending diagrams for the shaft. Determine the factor of safety against bending fatigue only at location F (centerline of Gear F) assuming 50% reliability and state in words if the shaft will have infinite life based on this location. T 1.500 1.25 Ø- BEARING 1.160 A E 4.5 0.375 & GEAR C 500 lbf C -1.75 Ø 3.0 & GEAR F 300 lbf FV -0.75 2.5 BEARING -0.50 0.0312 R- B 2.5 3/8 x 3/8 PROFILE KEYWAY -0.375 GEAR D 1.5625 KEYWAY DETAIL AT "F" 450 lbf D 1/4 x 1/4 PROFILE KEYWAY -1.25 Ø
The 40mm shaft shown in the figure has a bending load of 2kN and rotating with a torque of 0.9kN-m. The shaft has a yield strength of 325MPa. Using the design equation for maximum shear, determine the factor of safety of the mechanism.
Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb clockwise to 1000 in-lb counterclockwise as an applied bending moment at a critical section varies from + 4000 in-lb to 2000 in-lb. The shaft is of uniform cross section and no keyway is present at the critical sec- tion. Determine the required shaft diameter. The material has an ultimate strength of 80,000 psi and a yield strength of 60,000 psi. Base design on a factor of safety N=1.5. Take the endurance limit as half the ultimate strength.
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and ultimate tensile strength of 700 MPa. Diameters of the shaft are D=30 mm and d=20 mm. Fillet radius of the shoulder section is 2.5 mm. The shaft is rotating and subjected to steady bending moment of M=51 Nm, steady torsion of T=58 Nm and steady axial load of F=14 kN. The operating temperature of the shaft is 20 ᵒC and reliability is 99%. The shaft has ground surface. Calculate the alternating component of the normal stress (in MPa). (If there is no alternating component of the normal stress, enter "0" in the answer box)