A simply supported shaft is shown. A constant magnitude distributed unit load p is applied as the shaft rotates subject to a time-varying torque that varies from Tmin to Tmax. For the data given, find the diameter of shaft required to obtain a safety factor of 2 in fatigue loading if the shaft is steel of Sut = 745 MPa and Sy = 427 Mpa. Assume no stress concentrations are present. Dimensions: L = 8 cm, a = 4 cm, b = 8 cm, p = 1000 N/cm, Tmin = 0 N-m, Tmax = 2000 N-m STEP-BY-STEP don't understand English very well, so please write in clear letters. please

Q: The 2.0-in-diameter solid steel shaft shown is simply supported at the ends. Two pulleys are keyed…

A:

Q: The same shaft with keyway considered here again. Suppose that the shaft is working in ambient…

A: Given: CF=0.84Cs=0.88Cc=0.64Sf'=310 MPa

Q: In the figure below the shaft is simply supported in ball bearings at A and D. The shaft rotates and…

A:

Q: the propeller on a ship shown in figure qi is subjected to a compressive axial force f of 180 kn as…

A:

Q: Fatigue and Variable Loading Example 4 In the figure below the shaft is simply supported in ball…

A:

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

A:

Q: yield strength of oy 750 MPa. Determine the design factor of safety using Tresca and von Mises…

A: DefinitionTersca Theory:A ductile material fails or yields when its maximum shear stress equals or…

Q: The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces…

A: Given:- Shaft is made up of AISI 1035 CD steel Speed of shaft = 1000 rpm  To Find:-  Minimum…

Q: The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a…

A:

Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…

A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…

Q: 1) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is…

A: Treat the shaft as simply supported beam with supports at A and D.Here  are reaction forces at…

Q: Q2: Figure (2) shows a rotating shaft, simply supported at bearings atA and B. The shaft is loaded…

A:

Q: A solid 4340 HR Steel tie rod of length Lrod = 850 mm is employed to compress a 6061-T6 aluminum…

A: 4340 HR steel rod.Diameter of the rod, drod= 22.5 mmLength of the rod, Lrod= 850 mm6061-T6…

Q: 5. Fig Q5 shows a shaft of gearbox rotating about x axis. Shalt BC is a solid shalt with circul…

A: given; Fy=3KNradius(r1)=75mmFz=2KNradius(r2)=50mmshear stress(τ)=60MPalength(LBC)=400mmshear…

Q: 42, The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find…

A: Given: The static deflection of shaft, x= 0.36 mm

Q: A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.