Figure 2 shows the distribution of the wind load on the side of a 240 m tall tower. Use Trapezoidal method and Simpson's one-third rule to estimate the total wind force, in kN, on the side of the building (Do by hand and show all calculations). Building height (m) 22228 880 240 210 € 180 150 120 90 30 0 0,34 Wind loading (kN/m) 1,2 1,6 2,7 Figure 2. Distribution of Wind Load 3,2 3,1 3,5 3,8

Figure 2 shows the distribution of the wind load on the side of a 240 m tall tower. Use Trapezoidal method and Simpson's one-third rule to estimate the total wind force, in kN, on the side of the building (Do by hand and show all calculations). Building height (m) 22228 880 240 210 € 180 150 120 90 30 0 0,34 Wind loading (kN/m) 1,2 1,6 2,7 Figure 2. Distribution of Wind Load 3,2 3,1 3,5 3,8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 3 The wind blows uniformly on the front surface of the metal building with a pressure of 1.8 kN/m?. Determine the resultant force it exerts on the surface and the position of this resultant. y 2.5 m 1.0 m 2.5 m. 2.5 m.
9 ft 13 ft 22. Inad nianram Mj at point B is 10 kips-ft, P=12 kips is 9 ft from point A; and WI = 1.5 kips/ft is distributed along the length of the beam which is 22 ft. If the 1.5kips/ft uniformly distributed load will be transformed into a singular concentrated load, what will be the magnitude of Moment taken at point A? What is the equivalent singular Resultant force of the loads shown? Determine the location of the resultant R from point A.
Replace the distributed loading with an equivalent resultant force, and specify its location on the beam measured from point A. 15kN/m 10kN/m 3m
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
A transmission tower is subjected to the wind loads shown. Determine the axial force (kN) in member GE. J 1.5 m K >7 kN 1.8 m H >3 kN 1.8 m D E >5 kN F 1.8 m В 2.55 m 2.55 m
, shown below is being hoisted up with the force 1. The cylinder of weight, W= 380 kN F against the vertical wall. If us = 0.57 Ms W Ms a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion.
... 4m 2m Hinge Water 50cm 420cm 30cm B.
Consider a 3 metre long uniform beam with flexural rigidity of 100 kNm². The beam is supported with a fixed (clamped) support on the left, and a roller support 1 metre from the right hand side. 3m 2m A 1kN/m point load is applied 1 metre from the left hand side. If we find the deflection for this beam, using the boundary conditions for the fixed (clamped) end and for the roller support, we get the equation. y(z) 9600 ((16³-48x² +48r - 16) H(r− 1) - 112³ +18r²) (you do not need to calculate this yourself, but you may verify it if you wish) Have Desmos (or any other computer graphing system you like) draw a picture of the beam under load. Make sure the picture is accurate, and is zoomed appropriately to see the actual bends in the curve. What is wrong with the deflection function to the right of the roller support? b) Solve the deflection for this beam in two parts, as if there were two separate beams: 3m Om 2m 2m For the roller support use the following boundary conditions: y (2)= 0 and…
3. The Howe roof truss shown in the figure camries the given loads. The wind loads are perpendicular to the inclined members. Determine the magnitude of the resultant, its inclination with the horizontal, and where it intersects AB. 1100 N 2000 N 2500 N 1100 N 3.0 30 3.0 3.0 4000 N 2500N 1000 N
Compute the wind load acting on the short wall of the building based on directional method. A two- story essential facility shown in Figure 4.6 is an enclosed wood-frame building located in Seattle, Washington. The wall studs and roof rafters are 16 in. on center. Kzt = 1.0. 12 6.25 ft. 11 ft. 11 ft. 100 50 ft. Fig 4.6
Locate the position o maximum deflection. What is the deflection at 2 meters from the left? Concentrated Load = 350N, Triangular Load = 1700N/m Dimensions: Length = 1.0(2) = 2.0mm, Thickness = 40mm, Height = 200mm, Height - Thickness = 160mm
Wind blows on the side of a fully enclosed 30-ft-high hospital located on open flat terrain in Arizona. Determine the design wind pressure acting over the windward wall of the building at the heights 0–15 ft, 20 ft, and 30 ft. The roof is flat. Take Ke = 1.0.