For questions 1A, 1B, and 1C. The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. 1A. Assuming the beam is uniform, which of the following gives the absolute maximum shear?

For questions 1A, 1B, and 1C. The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. 1A. Assuming the beam is uniform, which of the following gives the absolute maximum shear?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 617 lb as shown. The span length of the cantilever beam is L = 4 ft. Determine the magnitude of the maximum bending stress in the pipe. O 21.55 ksi O 13.81 ksi O 15.73 ksi O 24.04 ksi O 17.18 ksi L B P d Pipe cross section. D
mm on its side, just 2. A cantilever, made of a certain material, of 2 m length and square section fails in bending when a point load of N is placed at its free end. A beam of rectangular cross section, and made of same material, 150 mm wide and 300 mm deep, is simply supported over a span of 3 m. Calculate: (a) the stress at which the cantilever beam fails in kPa and (b) the maximum concentrated load that the beam can carry at its center without failure in kN. 2 m (a) Cantilever kN THIS |— 1.5 m —— 1.5 m—| (b) Simply supported beam 150 300
The beam shown in figure carries a uniformly distributed load of w on overhang BC. The beam is constructed of a wood beam [E,=12 GPa] that is reinforced on its upper surface by a steel plate [E,-200 GPa] plate. Assume that the allowable bending stresses of the wood and the steel are o. = 9 MPa and o = 165 MPa, respectively. Determine the largest acceptable magnitude for distributed load w. [L = 4m, a = 1.25 m, b. =150 mm, d, =280 mm, b. = 230 mm, t, = 6 mm] IC
Concrete T-beam has been reinforced by bonding a steel plate to its web asshown below. The beam carries a uniformly distributed load of 40kN/m over a simply supported 8m span. Find the maximum deflection of the beam on the assumption that the concrete is fully operative in both tension and compression.(Est = 200kN/mm^2. Econc = 30kN/mm^2; central deflection due uniformly distributed load, total W acting on a simply supported beam of span L= 5WL^3/(384EI)) can someone please answer this question in detail who is confident in this topic with step-by-step calculations & sketch pls. I've asked this question twice now and I've gotten different answers each time so I'm at a bit of a loss. (DONT respond to this if you have already responded previously) Thank you
Need help ASAP Determine the max flexural stress in MPa
8
stresses in beams 3.
Please answer all, Strength of Materials. Thanks!
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
3. A solid steel shaft is loaded as shown in Fig. P-322. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 60 MPa and the angle of rotation at the free end is not to exceed 4 degrees. 750 N-m 1200 N-m 2.5 m 2.5 m-
Subject: