The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange B, determine the torque in pipe (1). 3 m 3 m 20 kN-m A (1) B (2) A 14.85 kN-m B 10.98 kN-m 9.40 kN-m 15.63 kN-m

The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange B, determine the torque in pipe (1). 3 m 3 m 20 kN-m A (1) B (2) A 14.85 kN-m B 10.98 kN-m 9.40 kN-m 15.63 kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 2014-T6 aluminum hollow column is fixed at its base and free at its top. The allowable bending stress is (b)allow - 38 ksi. The thickness of the wall for the section is t = 0.5 in. (Figure 1) Figure 3 in. 6 in. 6 in. P 8 ft 1 of 1 Part A Determine the maximum eccentric force P that can be safely supported by the column. Use the interaction formula. Express your answer to three significant figures and include the appropriate units. P = Submit ī Provide Feedback μA Value Request Answer · Units www ?
1. THE MEMBERS OF THE STRUCTURE SHOWN BELOW WEIGH 2918 N/M, DETERMINE THE SMALLEST DIAMETER OF PIN THAT CAN BE USED AT A IF THE SHEARING STRESS IS LIMITED TO 34470 kfa. ASSUME SINGLE SHEAR. 1.20 m 1.80m 1,20 M 0.90 m
Determine the maximum shearing stress of the beam
PROBLEM 04. Structure ABD shown is supported at pt. B by a 32-mm diameter rod and at pt. A by a 30mm diameter pin used in The rod is connected at pt. B and pt. C by 20mm diameter pins used in a double shear connection. single shear connections. Each of the pins has an ultimate shear strength of 320MN/m2. A concentrated load of P=45 kN acts as shown. Determine the following: c. the normal stress in rod BC d. the shearing stress in the pins at pt. A and B 5.0m 6.50m 1.5pm 4.50m
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 280 MPa, determine the minimum diameter d₂ required for rod (2). 80 KN d₁ O 18.2 mm O 28.7 mm O 24.6 mm O 30.2 mm O 21.7 mm 140 KN 140 KN B (2)
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 3650 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft.
Оиestion 3 Fig. 3a Part a: For the section shown, determine the: Maximum elastic Moment M 10 Fully plastic moment Mp NA Shape factor 2 If loaded about the horizontal axis o, = 250MN / m²; E = 200GN /m² 40 Part b: Determine the bending moment necessary to cause yielding to a depth of 10mm from the top and bottom surfaces. Fig. 3b If after applying this load it is subsequently removed. What will be the residual stresses NA which will result at A andB when the load is removed? Yielded region 40 09 09
Subject:
Determine the maximum normal and shear stresses