Consider the beam below (Note: distributed load is 1 k/ft) 20k | 10K 3K THT B 1o fr What is the magnitude of the vertical reaction at the pin? O 16.0 k O 18.5 k O 21.5 k O 24.0 k

Q: 30 KN 25 AN/M 2M IN A 30 KN 20 K

A: We have considered the pully to be frictionless and smooth.  So tension in cable is same as that of…

Q: 2m 2m 1.5m 2m IB D 2m V3 kN V 8 kN What is the reaction at support D in kN? Round off to two decimal…

A:

Q: 3D Equilibrium Solve for the tensions in the ropes if: Box Weight = 99 lb, z = 4 ft, y = 2 ft.…

A:

Q: A Determine the reaction forces at pin A and soller B (5 pts) 3 N/M 4m/m 4M 8m Answers must include…

A:

Q: ne B. Determine the resultant reactions at A and B. 600 Ib 12' B A

A: To find the resultant reactions at A and B -

Q: In a plate girder subjected to a bending moment of 200 kNm, the width and thickness of flange are…

A:

Q: Which of the following corresponds to the vertical reaction at the roller support? E 20 k 12 ft 12…

A:

Q: 10 k F 5 k 16 ft D 10 k E 16 ft A C В 12 ft - 12 ft Determine the Horizontal Reaction at C.

A:

Q: Water 18 radius

A:

Q: Determine the vertical reaction at B for the beam shown below. 3 50 k 1.5 k/ft 100 k-ft 30° \B…

A:

Q: A 6-meter simply-supported beam is loaded with a 2kN/m uniform load and a 10kN concentrated load at…

A:

Q: For the beam and loading shown, determine (a) the magnitude and location of the resultant of the…

A:

Q: E F P 3 m D 3 m 3 m 3 m P1 P.

A:

Q: For the figure MLM-1 below. Determine the vertical reactions at supports

A:

Q: The concrete dam is designed so that its face AB has a gradual slope into the water as shown. The…

A:

Q: PROBLEM NO. 2. A simply supported beam with overhang is loaded as shown. The beam has a…

A:

Q: bearing at A. Determine the resultant internal loadings acting on the cross section at C.

A: Given:- Total span of shaft = 3m             UDL acting = 800N/m             Point load acting =…

Q: In a plate girder subjected to a bending moment of 200 kNm, the width and thickness of flange are…

A:

Q: The beam shown in figure carries a triangular load which varies from 20 kN/m at A to 0 kN/m at B and…

A: Given:Required:Reaction at BLocation of zero shear from AMaximum momentMoment at point B

Q: The pin at C has a diameter xx(see table below). Assume that the pin supports at C is stated at the…

A:

Q: Two (2) beams are subjected to different loading condition and position as shown. A w1 w2 P x1 x2 x3…

A:

Q: 5. Determine the maximum live shear at C caused by the moving loads 80 KN 40kN 40kN 1m 2m 2m B 2m с…

A: Given data:

Q: QUESTION 5 A light uniform rod OAB is held by a ball-and-socket joint at O and supported by cable…

A: From the given question it is required to Determine the tension in the cable and reaction at ball…

Q: Analyze the structure below using cantilever beam method 25KN C 3m 50KN B 4m A F 6m- 8m SOLVE for…

A: Given data in question  Framed structure  Horizontal point loads Cantilever beam method To find out…

Q: JON | 20 N 10N 15N Com 8m B 4m Em 4m From the figure above, determine the: A. Resultant reaction at…

A:

Q: For the beam shown below, calculate: 0 hours: 24 minutes : 51 seconds f₁= 50 N/m F₂-300 N F₂= 200 N…

A:

Q: Problem No. 3. The pin at C is with a diameter C. Assume that the pin at C is supported as stated in…

A:

Q: A wide flange beam with dimension of: bf = 400 d = 500 tw = 12 tf = 18mm C is subjected to a V =…

A:

Q: Answer fast and draw diagram

A: Step 1: Reactions at SupportsThe total uniform load on the top horizontal beam:…

Q: Anwer ASAP

A: Draw free body diagram

Q: The side of the building in the figure is subjected to a wind loading as shown. The wind loading…

A:

Q: he box girder below is subjected to a shear of V=15kN. Determine the shear flow at point B. Give…

A: The magnitude of the shear force on the box girder = V = 15 kN To determine:- a) The shear flow at…

Q: Problem 02.Determinethereactions at A,B, andthe horizontal and vertical components of the internal…

A:

Q: Calculate the shear force V (in lb) and bending moment M (in lb-in.) at a cross section just to the…

A: Given:- To find:- Shear force and bending moment at just right of 810 lb load

Q: Problem 557 A cast-iron beam 10 m long and supported as shown in Fig. P-557 carries a uniformly…

A: Given : This is a problem of Structure analysis, where we are asked to determine the safe value of…

Q: What is the total resultant vertical load in the beam AB? (N) At what distance from A does the…

A: The figure shows a simply supported beam of16 m with uniformly varying load acting up to 9m from A…

Q: Draw the shear and moment diagram of the structure shown below.

A: Draw the free-body diagram of the beam. Write the equilibrium equation for the sum of the moment…

Q: What is the Maximum moment in kN-m. Given: W = 20, a = 2, b = 8, and P = 70. %3D PkN am W KN m b m R

A:

Q: In the truss shown in Figure. Determine the force member at AC. * 400 kN 800 kN 6 m D 3 m A: F 3 m 6…

A:

Q: B. Determine the support reactions at A, C & D of the loaded beam. 150 KN 45KN/m B 1.0 m 3.0 m 1.50…

A: To Determine Reactions at support A,C,D. There is no horizontal force, hence no horizontal reaction…

Q: Solve for the support reactions and draw and label the SFD and BMD

A: The given beam is shown below:

Q: Determine the maximum bending and shearing stresses developed in the beam 4. Ans. : (on)max= 240…

A:

Q: Analyze the frame and draw S.D and B.M? 10 kN/m B 5 m El constant 10 m

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.