4-49. Calculate the net force acting on the cone in Figure 4.69.1 mWater3 m-2 mFigure 4.69 System for Exercise 4-49.

Answered: Calculate the net force acting on the…

Engineering

Civil Engineering

Calculate the net force acting on the cone in Figure 4.69. 1m Water 3 m System for E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the pressure at the center of the pipe from the piezometer shown. 200mm WATER 75mmØPIPE

A: Given:- a piezo meter is attached to the pipe as shosn below

Q: Water is flowing into and discharging from a vertical pipe U-section as shown in Figure. At flange…

Q: 5 m When theta =-20 degrees, determine (a) the force exerted at B by the hydraulic cylinder BD. (b)…

Q: 3. A closed cylindrical tank 2 m diameter and 4 deep contains 3m depth of water. Air at a pressure…

Q: 3. A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in…

Q: 1. Compute the depth of the center of pressure from the bottom of a vertical circular gate having a…

A: Given,vertical circular gate of diameter “d” submerged in a liquid with its upper edge on the liquid…

Q: Gas having an internal pressure of 4 MPa is housed in the 3-meter-high pressure tank below. It…

A: A tensile Stress acting in the direction tangential to circumference is called circumferential or…

Q: 114 liters/second of water passes through the 30-degree elbow shaped on the side. The mass (M) of…

A: One of the crucial standards utilized in the examination of uniform stream is known as the…

Q: A shaft has an external diameter (ED) of 350 mm and an internal diameter of 150 mm. i) Calculate the…

A: There are various cross sections of shafts that are used in mechanical assemblies. Out of these the…

Q: 3. A closed cylindrical tank 2 m diameter and 4 deep contains 3m depth of water. Air at a pressure…

Q: 8-62 A horizontal pipe has an abrupt expansion from D₁ = 8 cm to D₂ = 16 cm. The water velocity in…

A: We have to find out the downstream pressure P2 and error if bernoulli's equation is used .

Q: Compute the reaction of the roller support of Beam CD. 10 KN 20 KN / m 5 KN / m А В 5 KN / m 50 KN-m…

Q: A rectangular gate 1.6 m wide is used as a partition as shown. One side has linseed oil filled to a…

Q: ing that water starts to evapor elow 2 kPa, determine the ma e diameter for this maximum-r at the…

A: Given Angle=6° Surface tension=1N/m Pressure drop=2kpa

Q: 3. A closed cylindrical tank 2 m diameter and 4 deep contains 3m depth of water. Air at a pressure…

Q: Underground water is pumped to a sufficient height through 10 cm diameter pipe that consists of a 3…

Q: • Given the beam as shown: 50 kN Determine: 20 kNm a.) Reaction at A. A B D b.) Reaction at B. 3 m…

Q: Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level…

Q: Determine the sag s for equilibrium of the system.

A: Given that :

Q: (50%): In a 45° bend a rectangular air duct of 1m? cross-sectional area is gradually reduced to 0.5…

A: Given:- Area at section 1, A1=1 m2Area at section 2, A2=0.5 m2Velocity at section 1,…

Q: A wooden circular board 1m in diameter is being submerged vertically in a liquid having SG=1.15. Its…

Q: The tank contains water, oil (S=0.8) and the pressure of the air with (90Kpa), the mass of the ate…

Q: horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5…

Q: A closed cylindrical tank 2 m. diameter and 4m depth with axis vertical contains 3m. depth of water.…

Q: For the sluice gate below, water is flowing under the gate in a rectangular channel (5 ft bottom…

Q: Water enters and leaves a T-shaped piece of pipe located in the horizontal plane. (1) the relative…

A: step 1-

Q: The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m…

Q: A circular door having a diam, of 3m closes a horizontal duct from a small diam. as shown. The…

A: Given:- The diameter of the circular door = 3 m The center of the door below the dam's water level…

Q: A solid shaft is transmitting power of 100kW at 400rpm. Calculate maximum shear stress developed on…

A: The formula to calculate the twist is given by, P=2πNT60 ...1 Here, P is power, N is…

Q: Air; P = 36 KPa Oil; SG = 0.82 1.7m Water 1.8m Unknown liquid 4.2m SG = 1.32 2m 60° Determine the…

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: The head, pressure, or power (are the same) is lost through running water in a pipe or station. Due…

Q: A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water…

A: Given data: Width of gate=1.6 m Height of gate=2m Inclination=45 degrees Water depth=1.5 m It is…

Q: Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61,…

A: Inlet diameter = d1 = 300mm Outlet diameter = d2 = 100mm Discharge = Q = .2m3/s Inlet pressure = P =…

Q: 3. A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in…

Q: Water is stored in a tank with an inclined panel AB whose dimensions are 2m long by 1.6m wide. The…

A: "Thank you for the question. As per our honor code we are supposed to solve the first three sub…

Question

4-49. Calculate the net force acting on the cone in Figure 4.69.
1 m
Water
3 m
-2 m
Figure 4.69 System for Exercise 4-49.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

H.W (1) Second week 1.1 l-60 and F-45O N, determine the magnitude of the rosultant force und its direction, measured counterckockwie from the positive x axis 700 N
434% @ P 4:29 I. Classroom ► docs.google.com • blö 10 Q1) For the force system shown in figure, 1) Find the angle (0) so that the resultant of these forces will be vertical. 45 kN 55 kN A 3. 1m 3 m 49.115 Deg. O 12.102 Deg. 42.833 Deg. 60.600 Deg. None of these LR:10. Q1: 2) Determine the macanitude of the. 11 + B.
PLS PROVIDE CLEAR SOLNS THANK YOU
Solve fast urgent
Figure Part A MBC = 170.8 15 m HÅ 2 m N•m 2m 0.5 m B ***** Submit Previous Answers Request Answer Determine the magnitude of the moment of the force F = {50i- 25 j - 80k} N about the base line BC of the tripod. (Figure 1) Express your answer to three significant figures and include the appropriate units. 1m ? 4 m 11 2.5 m 1 of 1
Structural anaysis Calculate reations and moment using 3 moment equations
Fluid mechanics, i need solutions in 10 minutes please. MCQ/Water in a tank is pressurized to 140 cm Hg, as shown in the figure. Determine the hydrostatic force per meter width on panel AB. A-211.108 kN B-405.235 KN C- 722.212 kN D- 345.281 KN E-1031.01 KN F- 851.273 kN G- 512.361 KN H- 58.014 kN I- 121.257 KN J-909.308 KN K-600.018 KN L- 89.789 KN
ANSWER ASAP. I NEED THE ANSWER IN 1 HOUR
The cantilever beam is loaded as shown in Figure Q2 (b). Use method of moment area to determine slope at point B and deflection at point C. Take EI as constant.
Avigid horizontal bar of negligible mas is Connected to two vods as shown in fig If w = 15 kg the Length 2m and Cross avea yoomm? and E 2108 Pa & Coefficients °F linear expansion ave 115 um(m.c) For steel rod and the Leng th 3.5 m, Cross avea 1500 mm, 2 85 GPa and Coffient oF linear expansion ave 19 um (m.c) for bronze rod. Compute the temperature change that will Cause the stress in the steel rod to be 65 M pa. bronze steel 1.5 15kg
03 Figure Q3 shows an overhead crane truss supported by pin and roller supports at point A and E. The truss is subjected to forces of 20 kN, 30KN and 20 KN acted at joint G, H and I, respectively. The cross-section area for the truss member is 2000 mm and the Young's Modulus for all truss members is 250 kN/mm. (a) As a structural engineer, you are responsible to ensure the overhead crane truss is safe during maintenance works. Therefore, the crane is additionally supported by roller support at joint C. Calculate reaction, Re at support C (assume the unit load acting downward)? (b) How do you present the new data on internal force for member BC when overhead crane has additional roller support at Joint C? (c) The new additionally roller support at joint C is placed on top of steel bearing plate. Check whether the square plate of 15 mm x 15 mm is safe or not safe to be used as the bearing plate. Maximum bearing capacity of the plate at joint C is 300 MPa.
4 kNm hisge 2 EN/m E 24 LN 5 m