The system below shows a solid shaft composed of 2 circular cross sections (H15 mm.r30 mm). It is fully restrained at both ends (i.e. fixed supported) and is subjected to torque Mo-38 kN.m. 2r2 A B If a = 1.5 m, b = 2.5 m. G = 772GPA The reaction at A is Select the correct response 19.895 kN.m 14.743 kN.m 6.750 kN.m 3.585 kN.m

The system below shows a solid shaft composed of 2 circular cross sections (H15 mm.r30 mm). It is fully restrained at both ends (i.e. fixed supported) and is subjected to torque Mo-38 kN.m. 2r2 A B If a = 1.5 m, b = 2.5 m. G = 772GPA The reaction at A is Select the correct response 19.895 kN.m 14.743 kN.m 6.750 kN.m 3.585 kN.m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Simple Beam: Compute the reaction, Ra= kN. Rh A Ra 2 m zJ KN B w = 10 kN/m 2 m Rc 1m 0
10. Determine the reaction at the roller support and draw the bending moment diagram for the beam and loading shown. The beam is W310X21 with E=190GPa and L=6m and load density of 2000N/m A DIOO ·L/2 L/2- IC -L12- B
C 1.5 m B 950 Nm 0.7 m 50 mm A The rod shown above is composed of two connected segments: AB is steel with shear modulus Gsteel = 75 GPa and BC is brass with shear modulus Grass = 40 GPa. The steel segment has a diameter of 50 mm. a) Determine the required diameter of the brass segment such that the reaction at A will equal the reaction at C under the applied torque of 950 Nm at B. b) What is the magnitude and direction of the reactions at A and C? c) What is the maximum shear stress developed in the steel and brass rods d) What is the angle of twist at B relative to C?
2. The structure below is supported by a pins at A and D. Determine the pin reactions at A, B, and D. (Hint: You will not be able to solve the equations of equilibrium for the entire structure initially.) A H 3-0" 400 lb 31-D" D TANA 600 lb 2' 0" 6_0"
Q.3 The solid steel shaft has a diameter of 20 mm. If it is subjected to the two torques, determine the reactions at the fixed supports A and B. 500 N m 03 m S00 N-m 15 m 0.2 m
The assembly consists of two 10mm diameter rods A-B and C-D, a 20 mm diameter rod E-F and a rigid bar H; point G is located at mid-distance between points E and F. All rods are made of copper with E = 101 GPa. If the magnitude of one force P is 10 kN, Determine reactions at points A, C, and F.
Step 1: Check reactions if solvable. If not, proceed solving ol members. For this problem, the reactions can be solve R1 = 1500 x 1.8 2700 N 1500 N/m C D 0.9m R2 = 900 x 2.4 = 2160 N 0.9 m 0.6 m B 900 N/m Ah 1.8 m RF Av Instructor: Mark P. De Gu Check 7700 N
B 300 mm ↑ 15 mm 70 KN 70 KN 20 mm 500 mm Steel Aluminum AMIN ATTIV 70 kN 70 KN + Rc A steel rod (20 mm diameter) 500 mm long is connected to two parallel aluminum rods (15 mm diameter) each 300 mm long via a rigid plate as shown. Two 70 kN loads at applied at the end of each aluminum rod. The structure is fixed at both ends resulting in a statically indeterminate system that can be treated as the superposition of two determinate systems as presented above. Note that Rc is the reaction at C. Assume Esteel = 200 GPa and Ealuminum = 70 GPa. a) Determine the reaction force at C, Rc b) Determine the reaction force at A and B and the normal stress in the steel and aluminum rods c) Which rods are in tension and which are in compression?
1. Describe three ways in which particle equilibrium problems differ from rigid body equilibrium problems. fixel pin The beam below is loaded as shown. It is to be supported at points A and C. Choose supports from the options below to place at each endpoint that would create a statically determinate problem. Then solve the problem to find the reactions at the supports. 20N HON A wir ↑ roller pin va or fixed HA 3
3) A load of 2,700 N acts on the machine part shown below. The machine part has a uniform thickness of 12 mm. Note: Point H will not be used in this problem and may be disregarded. a) Draw an FBD at showing the internal forces present at K. You may choose which side of the part to cut off. One method means you must find reactions at A and B. Choose the method that seems easier to you. b) Calculate the normal and shear stresses at point K (in MPa). [Ans. to check: = 0; ay = -10.89 MPa; Txy=-6.85 MPa] c) Draw the stress element at the point located at K. d) Calculate the normal and shear stresses if you rotate the element -20°. Draw a properly oriented stress element. 2,700 N 135 mm 60° C 50 mm 75 mm 50 mm X 40 mm # 12 mm 15 mm PH 40 mm OK y
1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free-body diagram of the beam. b. What are the magnitudes of the reactions at A and B? G 45% A 14" F -1.2 m 1.5 mlm- B 30°
A 8K 4K 16'-0" 1.5 K 4'-0" 4'-0" 4'-0" 4'-0" 2a. Support A is fixed. Calculate the reactions at support A. Show the reactions clearly on the diagram.