Water flows at a rate of 0.012 m³/s through a horizontal curved nozzle (gravity acts into the page) and leaves as a free jet at B. The free jet direction is e = 15°. The pressure at inlet A is 50 kPa. The diameter at A is 100 mm and the diameter at B is 70 mm.

Water flows at a rate of 0.012 m³/s through a horizontal curved nozzle (gravity acts into the page) and leaves as a free jet at B. The free jet direction is e = 15°. The pressure at inlet A is 50 kPa. The diameter at A is 100 mm and the diameter at B is 70 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question: The pressure pipe elbow with 30 degree orientation in the vertical plane is 60 cm in…

A: Solution

Q: Calculate the surface tension of the fluid (SG = 8.6) in the capillary tube below: Зтт h = 2mm e =…

Q: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a…

A: Using the continuity equation calculating the jet velocity: AV=AjVj…

Q: Water is flowing into and discharging from a vertical pipe U-section as shown in Figure. At flange…

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

Q: power output of the motor?

Q: 11.34. If the pressure at point A in the figure is 300 kPa, compute the volume flow rate of water at…

A: Pressure at Point A =300 kPa

Q: The flowrate of water through the bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is…

Q: -Air 45° Water dz -Mercury d2 7) Find the difference in pressure between tanks A and B if d, = 1 ft,…

A: Given data, d1= 1ft, d2=6in = 0.5ft d3= 1.5ft d4 = 8in= 0.67ft

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

Q: The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of…

Q: The centrifugal pump blades are 20 mm in depth at the outlet. The impeller is 250 mm in diameter and…

A: A centrifugal pump's impeller features backward-facing blades that are angled at 30 degrees to the…

Q: 6. Seawater (sg = 1.03) enters a heat exchanger through a reducing bend connecting a 4-inch copper…

A: Calculate the force required to hold the bend in equilibrium.

Q: Two vertical circular cylindrical tanks are connected near the bottom by a short tube having a…

A: t= 15.25 sec

Q: → The diameter of a pipe carrying oil (s=0.92) changes gradually from 400 mm at A to 600 mm at B.…

A: Given data in question Diameter Pressure Discharge To find out Direction of flow Frictional…

Q: For constant density flow through this round nozzle, V₁ = 1.7 m/s and V₂ = 20 m/s. The ratio of…

Q: Water flows steadily downward through the pipe shown in the figure below. Viscous effects are…

Q: A valve is suddenly closed in a 200 mmø pipe. The increase in pressure is 700 kPa. Assuming that the…

A: compute the water hammer pressure in kPa at the valve if it is closed in 3 sec.

Q: Oil (SG oil = 0.95) flows at 200 L/s through a 200mm diameter pipe, 500m long. Friction factor is…

A: Given data SG of oil = (Go) = 0.95 Friction factor (f) = 0.0225 Length of pipe (L) = 500 m…

Q: An incompressible fluid flows through a horizontal pipe which tapers from a diameter of 2 cm to a…

Q: Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of…

Q: Energy Equation The diameter from point B to the pump is 3 inches and the diameter from the pump to…

A: To find pressure at point B

Q: Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in…

A: Discharge, Q=2 L/s Diameter of the pipe, D=50 mm Roughness coefficient, k=0.03 mm Opening diameter…

Q: The triangular valve (AB) which weighs 1500 Newtons closed at point A and is free at point B. What…

A: Length of the gate t=2sin50o=2.6108 m Depth of center of gravity from surface of water…

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

Q: Problem 1. A 75-mm diameter orifice discharges 0.023 m3/s of liquid under a head of 2.90 m. The…

A: Given data, Diameter of orifice = 75 mm Discharge = 0.023 m³/s Head = 2.9 m Diameter at vena…

Q: An orifice 150 mm diameter, having a coefficient of contraction of 0.65 discharges oil (SG=D0.80)…

A: The correct answer is 0.93

Q: Given Water at 10°C flows at the rate of 970 L/min from the reservoir and through the pipe shown in…

Q: The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of…

Q: d leaves the other side of the tank through a pipe connected to the right amber at a rate of 4 L/s.…

A: Given:- Q=4×10-3 m3/secArea of orifice=501000 m2V=QArea=4×10-3502×10002=1.6 m/sec

Q: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a…

A: Given :

Q: a)Determine the difference in pressure between A and B in kPa if h = 0.15 and SG of oil is 0.862.…

Q: A tank contains gasoline sp. gr. = 0.90, oil sp. gr. = 0.8, and seawater sp. gr. = 1.03. If the…

A: Specific gravity for Oil = 0.8Gasoline = 0.9 Seawater = 1.03Depth of liquid for Oil = 0.5 mGasoline…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Water flows at a rate of 0.012 m/s through a horizontal curved nozzle (gravity acts into the page) and leaves as a free jet at B. The free jet direction is 0 =
15°. The pressure at inlet A is 50 kPa. The diameter at A is 100 mm and the diameter at B is 70 mm.
B
Determine the magnitude of the forces in the horizontal and vertical directions to hold the nozzle in place.
А. 131
|- v Horizontal Force =
v Vertical Force =
N
В. 183
C. 9.68
D. 375
E. 106
F. 29.9
G. 63.3
H. 45.6

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

B: A closed cylindrical tank filled with water has a hemispherical dome and is connected to an inverted piping system as shown in figure (1). The liquid in the top part of the piping system has a specific gravity of 0.8, and the remaining parts of the system are filled with water. If the pressure gage reading at A is 60 kPa. Determine: (a) the pressure in pipe B, and (b) the pressure head, in millimeters of mercury, at the top of the dome (point C). Hemispherical dome. PA=60kPa. 3m water 4m 3m 2m Water 7 SG=0.8 Fig. (1)
A 75 mm diameter orifice discharges 0.023 m3/s of liquid under a head of 2.90 m. The diameter of the jet at the vena contracta is found by calipering to be 66.25 mm. Compute the coefficient of discharge. Determine for the coefficient of contraction. Find the coefficient of velocity.
Two pipes A and B are connected in parallel between two points. Pipe A is 200 m long and has a diameter of 16 cm, pipe B is 150 m long and has a diameter of 12 cm. Both the pipes have the same friction factor of 0.018. A partially closed valve in pipe 'A' causes the discharge in the two pipes to be the same. All other minor losses can be neglected. The value of the valve coefficient is - Valve F = 0.018 L=200m, d-16cm L,=150m, d=12cm B F = 0.018
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
The gage pressure (psig) at point a is nearest (a) 13.7 (b) 14.7 (c) 101.3 (d) 0 (e) 1 Oil a 3 in SG = 0.69 SThe gage pressure (psig) at point c is nearest (a) 57.2 (b) 1.4 (c) 6.7 (d) 0.4 8 in Water The absolute pressure (psia) the natural gas pipeline is nearest h, = 22 in (a) 8.4 (b) 65 (c) 9 (e) 23 16 in SThe gage pressure osig) in the natural gas pipeline is Natural gas Dif the pipeline pressure was increased by 50%, what cost- effective manometer modification(s) might be needed? (b) More mercury, less oil (c) Add 2 more manometer loops (d) Replace the manometer with a high-pressure gage (e) Rotate the gas line to a vertical alignment Mercury SG = 13.6
The flow is opened to the atmosphere at point D which is fed by a very wide reservoir that has a water surface elevation of (5+) meters as shown in the figure given below. Elevation of the horizontal axis BC is 1 meter. At sections AB the diameter of the pipe is (0.2+- meters and CD the diameter of the 100 pipe is (0.3+: meters. The flow is ideal (inviscid) and absolute atmosphere pressure is 9.81 N/cm?. Considering the pipe's diameter is (0.15+; m at section BC, find the discharges and the 100 а. velocities of the flow at other sections (AE, EB, BC, CF, FD). Draw the energy and hydraulic grade lines of the system. b. Assuming the system discharge is constant and has the value you have found in (a), calculate the minimum pipe diameter that the section BC can take and draw the energy and hydraulic grade lines of this situation. Note: Absolute vapor pressure of water is 2.26 kN/m?. 10 A E 2.5 D B m
tank contains water upto a height of 1 m above the base. An immiscible liquid of sp. gr. 0.8 is filled on the top of water upto 1.5 m height. Calculate : () total pressure on one side of the tank, () the positiom of centre of pressure for one side of the tank, which is 3 m wide.
Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 97.1 kPa. The gage pressure at section (1) is 103 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 103 kPa, V₁ = 4 m/s. (a) Kx = i 2260.24 (b) to the left N V₂ 160 mm Section (2) 300 mm V₁ Water Section (1) P1 V₁
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m