An inclined rectangular gate (length 2m, wide 1m) as shown in Fig.2 hinged at point A.The tank contains water, oil (S=0.8) and the pressure of the air with (90Kpa), the mass of thegate is (100 Kg). Calculate the magnitude, direction and the location of the force acting uponthe gate?1.5mUAIROILWATERS=13.62m

Answered: Image /qna-images/answer/84666295-db4e-4f87-a916-6e545d8906ca.jpg

The tank contains water, oil (S=0.8) and the pressure of the air with (90Kpa), the mass of the ate is (100 Kg). Calculate the magnitude, direction and the location of the force acting upon he gate? AIR OIL WATER S=13.6 2m

The tank contains water, oil (S=0.8) and the pressure of the air with (90Kpa), the mass of the ate is (100 Kg). Calculate the magnitude, direction and the location of the force acting upon he gate? AIR OIL WATER S=13.6 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Heavy fuel oil flows at Q = 10 gallons per minute (gpm) in a horizontal steel pipe that connects two storage tanks. The diameter of the pipe is D = 1.5 inches. The length of the pipe is L = 100 feet. The depth of oil in the supply tank is 30 feet above the pipe entrance. The temperature of the oil is 60°F, the specific gravity of the oil is s.g.oin = 0.90, the specific weight of the oil is 56.13 lb/ft', and the kinematic viscosity of the oil is 0.00175 ft2/s. The pipe discharges into the bottom of the receiving tank. Neglect minor losses. a) Determine the pressure p at the pipe entrance in pounds per square foot (psf). b) Determine the velocity v in feet per second (fps). c) Determine the Reynolds number Re. d) Classify the flow based on the Reynolds number Re. e) Determine the Darcy-Weisbach friction factor f. f) Determine the friction head loss hfac in feet in the pipe between the two storage tanks. 8) Determine the depth of oil in feet above the exit from the pipe into the second…
A body A rests on a smooth horizontal table. Two bodies of mass 2 kg and 10 kg. hanging freely, are attached to A by strings which pass over smooth pulleys at the edges of the table. The two strings are taut. When the system is released from rest, it accelerates at 2ms. Find the mass of A. T4 2 kg 10 kg
Fluid Mechanics. Reg.no : 5393 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.
Question 1: Equilibrium of rigid body The uniform beam AD, which is supported by pin at point A and by roller at point C, carries the loads as shown in the figure below. Neglecting the weight of the beam and considering the system to be at equilibrium, (a) draw the free body diagram of the system (b) determine the reactive force at point C (c) determine the reactive forces at point A. 120 kN/m -2m- 100 KN B 2 m C + 120 kN/m o 2m 30⁰ D 120 kN
QI: In Figure below find the resultant pressure force and the depth of the centre of pressure on the cylinder gate of diameter 4ft which has a circular hole of 0.9 ft diameter located above the centre of the main gate by I ft. 1.2n Oil, S-0.8 D-9n
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
A U-tube of uniform cross-section has both arms open to the atmosphere. The U-tube contains three immiscible liquids, with density PA, PB, and pc, as depicted in the diagram below, where po is the atmospheric pressure. We denote h to be the depth of the open surface of liquid A on the left arm, relative to the open surface of liquid Con the right arm. I is the depth of the interface between liquid B and C on the right arm and 2l is the depth of the interface between liquid A and liquid B on the right arm. Po PA (c) Po PC PB е е (a) Explain why the liquid densities need to satisfy the condition PA PB PC. (b) Write down an expression for the pressure at depth z below the surface of liquid A in the left-hand part of the tube. Show that l < h < 2l if PB + PC < PA•
Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. 1m Liquid (s.g. = 0.88 ) 4 m B 2.6 m 1 m 幸 +
6) Turbulent water flows from a tank to a pipe. The head loss relationship in the pipe can be 25 (-)). What is the discharge of water? described as h₁=0.025 몰 Water T = 60°F Elevation 100 ft D = 1 ft ↓ ↑ L = 1000 ft Elevation 60 ft 6 in. diameter jet
4. A moment M applied about the hinge A helps the stainless-steel gate in the figure hold fresh water in storage. Calculate the necessary M to just hold the gate closed against the lip of the container at C if the specific weight of the fresh water in tank is 62.41 lb/ft³, the width of the gate is 80 in, the weight of the gate is 120 lb, and the Point G in the figure shows the center of gravity of the gate. 40 in AM 70 in 50 in B G 60⁰ 25 in
The tank shown has one curved surface restraining a body of static fluid, with the following dimensions: w = 5.25 m h1 = 2.4 m R1 = 0.90 m Required Compute the magnitude of the resultant force, in kN, to the nearest 100th. Water h1 R1
Determine the transfer function of the two- tank cascade system where qi is the input and he is the output variable. ↓qi h₁ A₁ R₁ Figure 2 A₂ h₂ R₂ qo