Figure 2: Schematic for Question 2. A uniform slender rod of length L = 900 mm and mass m = 4 kg is suspended from a hinge at C. A horizontal force P of magnitude 75 N is applied at end B. Knowing that r= 225 mm, determine (a) the angular acceleration of the rod (b) the components of the reaction at C (c) the distance r for which the horizontal component of the reaction at C is zero (d) the corresponding angular acceleration of the rod

Figure 2: Schematic for Question 2. A uniform slender rod of length L = 900 mm and mass m = 4 kg is suspended from a hinge at C. A horizontal force P of magnitude 75 N is applied at end B. Knowing that r= 225 mm, determine (a) the angular acceleration of the rod (b) the components of the reaction at C (c) the distance r for which the horizontal component of the reaction at C is zero (d) the corresponding angular acceleration of the rod

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniform 144-lb cube is attached to a uniform 136-lb circular shaft as shown, and a couple M with a constant magnitude is applied to the shaft when the system is at rest. Knowing that r = 4 in., L= 12 in., and the angular velocity of the system is 960 rpm after 4 s, determine the magnitude of the couple M.
Can you explain the radius of gyration ? why is it 480mm for the rod & 120mm for the disk. How do we figure this out ? thank you
Problem # 5) A pulley having a moment of inertia of 0.191b-ft-s² is connected to two masses as shown. The masses A and B have linear acceleration of 1.85ft/s² upward and 1.11 ft/s² downward, respectively. Assuming no axle friction, determine (a) the tension forces TA and TB in the cables connecting the masses, and (b) the angular acceleration a of the pulley. Include and present the Free Body Diagram and Inertial Response Diagram as part of the solving process. Hint #1: Hint #2: use mA = 0.1553slugs, and mв = 0.3106slugs treat each body separately 6 in. B 10 lb 10 in. A 5 lb
A 240-lb block is suspended from an inextensible cable which is wrapped around a drum of 1.25-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of intertia of 10.5 lb-ft-s^2. At the instant shown, the velocity of the block is 6 ft/s directed downward. The bearing at A as a frictional moment of 60 lb-ft. What is the kinetic energy of the system after the block moved after 4ft? (in ft-lb)
A 197-kg flywheel is at rest when a constant 300 N·m couple is applied. After executing 560 revolutions, the flywheel reaches its rated speed of 2400 rpm. Knowing that the radius of gyration of the flywheel is 400 mm, determine the average magnitude of the couple due to kinetic friction in the bearing. N.m. The average magnitude of the couple due to kinetic friction in the bearing is [
A stationary horizontal plate is attached to the ceiling by means ofa fixed vertical tube. A wheel of radius aa and mass mm is mounted on a light axle ACAC that is attached by means of a clevis at AA to a rod ABAB fitted inside the vertical tube. The rod ABAB is made to rotate with a constant angular velocity ΩΩ causing the wheel to roll on the lower face of the stationary plate. Determine the minimum angular velocity ΩΩ for which contact is maintained between the wheel and the plate. Consider the particular cases ( aa ) when the mass of the wheel is concentrated in the rim, (b) when the wheel is equivalent to a thin disk of radius aa also extend the problem using Kinematic and Kinetic analysis
!
The rotor of an electric motor has an angular velocity of 3600 rpm when the load and power are cut off. The 120-lb rotor, which has a centroidal radius of gyration of 9 in., then coasts to rest. Knowing that kinetic friction results in a couple of magnitude 2.5 lb·ft exerted on the rotor, determine the number of revolutions that the rotor executes before coming to rest.
Part A The 21-kg roll of paper has a radius of gyration kA = 90 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests against a wall for which the coefficient of kinetic friction is u = 0.2. Neglect the mass of paper that is removed. (Figure 1) Determine the magnitude of the constant vertical force F that must be applied to the roll to pull off 1 m of paper in t = 3 s starting from rest. Express your answer to three significant figures and include the appropriate units. TH HẢ ? F = Value Units Submit Request Answer Provide Feedback Figure < 1 of 1 300 mm 125 mm
Do not give answer in image formet and hand writing
6
An automobile wheel test rig consists of a uniform disk A, of mass mÃ = 5000 kg and radius rÃ = 1.5 m, that can rotate freely about its fixed center C and over which the wheel of an automobile is made to roll. A wheel B, whose center and center of mass coincide at D, is mounted on a shaft (not shown) that holds D fixed while it allows the wheel to rotate about D. The wheel has diameter d = 0.62 m, mass mß = 21.5 kg, and mass moment of inertia about its mass center /D = 44 kg-m². Both A and B are initially at rest when B is subject to a constant torque M that causes B to roll without slip on A. M B d A If M = 1200 N·m, use the angular impulse-momentum principle to determine how long it takes to reach conditions simulating a car speed of 100 km/h. The automobile wheel test rig takes s to reach conditions simulating a car speed of 100 km/h.