150 mm 120 mm 150 mm 80 mm B @2 60 mm

Q: A homogeneous rectangular plate weighing 40 lb is suspended from two frictionless pins A and B. If…

A: (a) The free body diagram of a homogenous rectangular plate, when pin B is suddenly removed is given…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The tension in cable AC is T=26.8 N The mass of AB rod  is ma=3.5 kg. The mass of BC rod is mb=2 kg…

Q: (5) The uniform slender rod (mass m and length L) is pinned to the center of the uniform disk (mass…

A:

Q: A 200-kg flywheel is at rest when a constant 300 N.m couple is applied. After executing 560…

A: Write the expression of the moment of inertia of the flywheel. Write the expression of the initial…

Q: Problem 2: A uniform slender rod, 4 ft long and weighing 50 Ib, hangs freely from its end A. A…

A: Given data: The length of the rod is L = 4 ft. The weight of the rod is W = 50 lb. The magnitude of…

Q: A thin, homogeneous disk of mass m and radius r spins at the constant rate w about an axle held by a…

A: → Given data ,      mass of disk is m      radius of the disk is r     spins at the constant rate…

Q: If the earth were a sphere, the gravitational attraction of the sun, moon, and planets would at all…

A: The time period of the earth’s precess about GA is The velocity of precession about GA axis is

Q: An excavator encounters a reaction force of 7600 lb from the ground, normal to line AC, as shown.…

A:

Q: A particle, of mass 2 kg, is attached to one end of a light inextensible string. The other end is…

A: Given Mass of Particle, m=2 kgRadius of horizontal circle, r=0.6 mString Angle with vertical, θ=30°

Q: Figure 2: Schematic for Question 2. A uniform slender rod of length L = 900 mm and mass m = 4 kg is…

A:

Q: The 10-oz disk shown spins at the rate w1 = 750 rpm, while axle AB rotates as shown with an angular…

A: The angular velocity vector is: Let the origin be at C with the centroidal axis x, y, and z.

Q: A disk with mass m and radius R is released from rest at a height h and rolls without slipping down…

A: The disc rolls without slipping.

Q: Two disks of the same material are attached to a shaft as shown. Disk A has a radius r and a…

A: To find  The value of n Given  The radius of disk A ra is r. The thickness of disk A  ta is 2b. The…

Q: 2. Two 20-kg uniform bars are connected to form the linkage shown. Neglecting the effect of…

A:

Q: The 4-kg uniform slender bar BD is attached to bar AB and a wheel of negligible mass that rolls on a…

A: Apply the kinematics to the given system. Therefore,

Q: Pravinbhai

A: Step 1:Given data:Weight of the rod BD , WBD​=3lbangular velocity of crank AB,ωAB​=16rad/sAngular…

Q: A 300 X 400 mm rectangular plate of mass 30 kg is suspended from tw pins A and B. If pin B is…

A:

Q: 16.77 A uniform slender rod of weight 0.24 lb/ft is used to form the assembly shown. The assembly…

A: The given data is as below: Rod weight w = 0.24 lb/ft Speed N = 120 rpm radius of slender rod r = 8…

Q: Problem 2: The drum shown weighs 80lb and has a mass moment of inertia about O of 0.8 lb.ft?.…

A:

Q: Bar BC weighs 161 lb and has a radius of gyration of mass with respect to a hor- izontal axis…

A:

Q: Given: The gear shown moves on a fixed horizontal rack. The gear has mass m and a radius of gyration…

A: Given: Mass of the gear=mgear Radius of gyration of the gear=R Mass of the rod=mrod Length of the…

Q: Consider a rigid body initially at rest and subjected to an impulsive force F contained in the plane…

A: a)The impulse-momentum diagram for the given rigid body is as follows.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.