Figure 1.2 shows a floor plan consisting of a one-way slab spanning betweenbeams on grid lines A, B, C, and D. The beams are supported on columns at theintersections of numbered and lettered grid lines. Unfactored dead and live loadscarried by the slab are shown. a)Compute the factored dead and live loads based on 1.2D and 1.6 L. b)Determine the tributary width for the beam on Line B and the total factored load (plf) carried by the beam. (Neglect beam weight) c) Determine the tributary area for the column at the intersection of Lines B and 2. Compute the total factored load (lbs) transferred to the column. Assume the column is 12 in. x 12 in.

Figure 1.2 shows a floor plan consisting of a one-way slab spanning betweenbeams on grid lines A, B, C, and D. The beams are supported on columns at theintersections of numbered and lettered grid lines. Unfactored dead and live loadscarried by the slab are shown. a)Compute the factored dead and live loads based on 1.2D and 1.6 L. b)Determine the tributary width for the beam on Line B and the total factored load (plf) carried by the beam. (Neglect beam weight) c) Determine the tributary area for the column at the intersection of Lines B and 2. Compute the total factored load (lbs) transferred to the column. Assume the column is 12 in. x 12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported 1 way slab having span of 3 meters is to carry the load for DL = 5kpa and LL = 4.8Kpa. If the concrete f'c = 28Mpa and rebar to be used is 10mm with fy = 276Mpa. a.) Determine the minimum thickness of the 1 way slab.(answer in millimeter in whole number) b.) Determine the Ultimate loading combination for the slab considering 1 meter strip?(answer in KN/m. in 3 decimal places ) c.) Determine the Ultimate moment for the slab considering 1 meter strip?(answer in KN-m. in 3 decimal places) d.) Determine the effective depth of the slab considering concrete cover = 20mmanswer in millimeter. in whole number e.) Determine the area of reinforcement for the slab based on the actual loadings.(answer in sq.mm. in 3 decimal places) f.) Determine the spacing of the rebar.(answer in millimeter(Don't round up, use actual value). in 3 decimal places)
H.W.1: One-Way Slab: 1. Check slab thíckness. 2.Check shear force. 3.Design flexural reinforcement for the slab. I 4.Dosign flexural roinforcement for continuous beam B. fe=28Mpa 6m 5.8m 5.8m 6m f,-420Mpa Slab h=250mm 6m Beam Section: ha600mm bw#350mm Column Section: 500x500mm 7m LL=5kN/m? Exterior D.L-4kN/m? 7m K
2. Design a one-way slab to carry a service live load of 4000 Pa. The slab has a length of 4m with both ends continuous. Assume f'c = 21MPa and fy = 415 MPa for main bars and fy=276 MPa for temperature bars. Unit weight of concrete is 23.5 kN/m³.
Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the tributary width. Colored box represents columns and uncolored represents beams.
A timber beam 97 mm wide by 160 mm high is subjected to a vertical shear V = 28 kN. Determine the shearing stress developed at layer 3 only 20 mm apart from the top to bottomn of the section. Answer must be in MPa.
Need Complete an elaborate solution Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete fc’ = 25MPa and ASD.
a square footing 2.4 m x 2.4 m x 0.45 m thick supports a 300 mm square column at its center. column loads are at service conditions dl = 346 kn, ll = 231 kn, fc' = 21 mpa, and fy = 415 mpa. concrete cover to the centroid of steel reinforcement is 100 mm. calculate the nominal one way shear stress in the slab
The slab shown below using f'c= 25 MPa and fy = 420 MPa. The service dead loads are 5 kN/m including its own weight and service live loads are 7 kN/m?: 1- Find area of steel required for the slab. 2- Area of steel required for interior beam B1, at critical section. 6.0 m 6.5 m 6.0 m 0.3m 0.3m 4.5 m 4.5 m 0.3m 0.3m B. 4.5 m 4.5 m 0.3m 0.3m He 6.3m 0.3m 0.3m 0.3m
Figure 1.2 shows a floor plan consisting of a one-way slab spanning betweenbeams on grid lines A, B, C, and D. The beams are supported on columns at theintersections of numbered and lettered grid lines. Unfactored dead and live loadscarried by the slab are shown. a)Compute the factored dead and live loads based on 1.2D and 1.6 L. b)Determine the tributary width for the beam on Line B and the total factored load (plf) carried by the beam. (Neglect beam weight) c) Determine the tributary area for the column at the intersection of Lines B and 2. Compute the total factored load (lbs) transferred to the column. Assume the column is 12 in. x 12 in. 22-144 200 SHEETS O 3 18' SE Dead: Live: 20' Unfactored Loads W₁ = 100pst W₁ = 70 psf Beam on Line B: Column on Beams Line B/2 Columns One-way slab 4 FLOOR PLAN 20' Trib.width = C 1 Trib. area = - Factored Loads_ 20' Beam Load= Column Load=
Please please correct answer
Design a simply supported one- way slab with ln=4m. Let fy=276MPa, f’c=21MPa, db=10mm and Cc=20mma. Determine the thickness of the slabb. Determine the required reinforcement spacing and check the for minimum and maximum values set by NSCP.
Kindly write the COMPLETE solution NEATLY. Thank you