View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of 7.675 in. and a wall thickness of 0.25 in. The timber beam is 10.75-in.-wide, and the upper plate has the same width. The load imposed on the column by the timber beam is 98 kips. Determine the average bearing stress at the surfaces between the pipe column and the upper and lower steel bearing plates. 10,75 in. Timber beam Upper bearing plate Steel pipe Lower bearing plate Concrete slab a a O 15.69 ksi O 22.87 ksi O 11.89 ksi O 16.81 ksi O 19.75 ksi

View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of 7.675 in. and a wall thickness of 0.25 in. The timber beam is 10.75-in.-wide, and the upper plate has the same width. The load imposed on the column by the timber beam is 98 kips. Determine the average bearing stress at the surfaces between the pipe column and the upper and lower steel bearing plates. 10,75 in. Timber beam Upper bearing plate Steel pipe Lower bearing plate Concrete slab a a O 15.69 ksi O 22.87 ksi O 11.89 ksi O 16.81 ksi O 19.75 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
The cross section of a reinforced concrete beam is shown below .( 5 - No . 10 bars )are designed as the bottom bars and No. 3 stirrups as the vertical reinforcement . Considering a clear cover thickness = 1.5 in , sketch the layout of reinforcement and show bar spacings per AC1318-19 . Assume maximum aggregate size = 1 in and the minimum required effective depth of bottom bars = 20 inches .
Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
A timber beam 97 mm wide by 160 mm high is subjected to a vertical shear V = 28 kN. Determine the shearing stress developed at layer 3 only 20 mm apart from the top to bottomn of the section. Answer must be in MPa.
6
ALLE A square lead slab of side 50 cm and thickness 10 cm is subjected to a shearing force (on its narrow fa of 9 x 104 N. The lower edge is riveted to the floor. How much will the upper edge be displaced? (Shear modulus of lead 5.6 x 109 N m²) (4) 1.6 cm (1) 0.16 mm (2) 1.6 mm (3) 0.16 cm
The sign post shown has an outside diameter of 12-in. and a wall thickness of 0.50-in. Determine the maximum load P that can be applied while limiting the maximum tensile stress at the base to < 36 ksi. 1.5P P 10 ft 7 ft C 20 ft D.
*Subject: Reinforced prestressed concrete - Civil Engineering *Please refer for my attached formula or guidelines solve this problem A one-way both ends continuous slab is to support the moments tabulated. Consider L=5m, Fc’=21MPa and fy = 415 MPA. Dead load Moments: +42kN.m at midspan ; -67 kN.m at support Live load Moment: +40kN.m at midspan, -44kN.m at support. Determine the minimum thickness of the slab.
A one way simply supported slab of effective length in the shorter span is 3.5 m. Calculate the area of the distribution reinforcement.
Complete answer