A one room service building is shown in Fig (1), All walls are bricks walls with thickness -0.36 m 036 Example130 20r &8 Slab thickness=t = given in table, If it is reinforced with at top and bottom and in both directions as in table below. a- Find the maximum live load that can be applied safely. 0.36 036 Note : Do not check the shear. ム 0.36 Fig (1) Reinforcement L1, L2, t, We spacing m mm kN/m 5.25 ? 20 350 #10@175 3.5 100

A one room service building is shown in Fig (1), All walls are bricks walls with thickness -0.36 m 036 Example130 20r &8 Slab thickness=t = given in table, If it is reinforced with at top and bottom and in both directions as in table below. a- Find the maximum live load that can be applied safely. 0.36 036 Note : Do not check the shear. ム 0.36 Fig (1) Reinforcement L1, L2, t, We spacing m mm kN/m 5.25 ? 20 350 #10@175 3.5 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
Question 8 1 p The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec=23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 TE 730 N12 ligs (fsv.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the concrete stresses in tension and compression of the reinforcement concrete beam shown in Figure 3. Compression concrete stress Choose ] Tension Concrete stress Choose]
21 in. 24 in. f'. = 6.5 ksi fy = 50 ksi E. = 3,600 ksi n = 8.0 Mcr = 1029 k-in. 3 #8 -16 in.- + 3 in. FIND: Determine stresses in the concrete and steel at M = 1200 k-in. and enter the following values below. Pay attention to units and round values as specified, then use the rounded values for further calculations. f. = ksi (round to nearest hundredth; i.e., 0.00) ksi (round to nearest tenth; i.e., 0.0) %3D
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
X = 165 Y = 40 Z = 25 D = 500
Shear and Movement Diagram. Tee Beam Analysis
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
please include also the given, required and the solution thank you
Help pls. Ill upvote :)