F12-5. If the beam is made from four plates and subjected to a shear force of V = 20 kN, determine the shear stress at paint A. Represent the state of stress on a volume element at this point. So mm Omm smm 130 mm O 25 mm- 150 mm So mm

Q: Determine the magnitude of the maximum shear stress on the stress element for which σx=-87 MPa,…

A:

Q: 80 mm 12 mm 60 mm 112 mm 20 mm

A: Maximum shear stress in the symmetric I section is at the neutral axis.

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given data as per question Diameter of cable AB = 12mm Diameter of cable AC = 10mm Mass = 2 Mg =…

Q: 2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the…

A:

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: 1-42. Determine the average shear stress developed in pin A of the truss. A horizontal force of P =…

A: The free body diagram of the truss is as follows:

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: $1-12. Determine the resulta on the cross sections at points F

A: Draw the schematic diagram for the system.Apply the moment equilibrium condition at point A.

Q: If the beam is made from four plates and subjected to a shear force of V = 20 kN, determine the…

A: Write the expression of the moment of inertia of the plates about the neutral axis. Write the…

Q: Determine the internal normal force at section A if the rod is subjected to the external uniformly…

A: Given data: The axial uniformly distributed load in the bar is given as F = 8 kN/m.   Free body…

Q: 1-32. Determine the largest intensity w of the uniform loading that can be applied to the frame…

A: For the solution refer below images.

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: 30° 1-3. Determine the resultant internal normal and shear force in the member at (a) section a-a…

A: As per given  We have to determine normal force and shear force in the member

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: Given, The diameter of AB(dAB) = 4 mm The diameter of BC(dBC) = 6 mm Load (P) = 3 kN For Member…

Q: 1-50. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: Determine the maximum shear stress in the strut if it is subjected to a shear force of V = 20 kN.

A: Given data V=20 KN

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given: The mass of the concrete pipe is m=2 Mg. The diameter of the cable AC is d’=10 mm=0.01 m.…

Q: All pins are subjected to double shear, and each has a diameter of 16 mm A) If P= 20 kN, determine…

A: