F = 5 kN 75 mm 150 mm 50 mm 350 mm B F, = 7.5 kN 250 mm

Q: The plate is made of Tobin bronze, which yields at sY = 25 ksi. Using the maximum distortion energy…

A: Given data as per question

Q: A loading condition is shown below. The wires at point A and D both made from a steel with the yield…

A: Drawing the free body diagram of the given question:-

Q: The turbine develops 360 kW of power, which is transmitted to the gears such that both B and C…

A: GivenP=360 kWPB=PCd=110 mmω=360 rev/minG=75 GPa=75×103  MPa=75×103  N/mm2

Q: re B 400 mm Sk ← 55 400 mm 60 kN ▾ Part A If the 20-mm-diameter rod is made of A-36 steel and the…

A: To find: The deflection in the rod. Given: The diameter of the rod is d=20 mm. The stiffness of the…

Q: If the A-36 steel pipe has an outer and inner diameter of 20 mm and 10 mm, respectively, determine…

A: The maximum distortion energy theory is also named as von mises theory In this theory failure occurs…

Q: The two pulleys fixed to the shaft are loaded as shown. If the journal bearings at A and B exert…

A: The above question is solved in following steps: 1. Calculate the reactions at the end supports…

Q: *11-40. The end gear connected to the shaft is subjected to the loading shown. If the bearings at A…

A: Given: The yields strength of material = 80 MPa

Q: A pipe has an outer radius of 2in and an inner radius of 1.7 in, it is subjected to the forces…

A: GivenP=150 lbT=20 lb ft=20×12=240 lb inro=2in     ie. do=4inri=1.7in    ie. di=3.4in

Q: The 304-stainless-steel cylinder has an inner diameter of 4 in. and a wall thickness of 0.1 in. O…

A:

Q: ing a The rigid beam is supported by a pih at A and tWo steel wi If the yield stress for the wires…

A: Givenσy=530MPaEst=200GPad=4mmL=800mm

Q: If a shaft is made of a material for which sY = 75 ksi, determine the maximum torsional shear stress…

A: Given: The yield stress of the material is sY=75 ksi.

Q: Determine the diameter of a red brass C83400 bar that is 8 ft long if it is to be used to absorb 800…

A: Given data as per the question Length of bar =8 ft energy absorbed =800 ft.lb considering properties…

Q: For the material indicated determine the required diameter of the rod.

A:

Q: If the temperature of the 85 mmmm diameter post CD is increased by 60 ⚫C, determine the force…

A:

Q: 4. The shaft shown below, is made of ASTM-A-36 steel with Sy = 250 MPa and p = 7.86 g/cm³. The…

A: The weight density is The yield stress is The torque aplied is The length of shaft is

Q: Problem 4. The structure in the figure is composed of two rigid bars (AB and CD) and two vertical…

A: The free-body diagram of the beam is as shown below,   Assumption: Let the length of aluminum and…

Q: 3-34. A shear spring is made from two blocks of rubber, each having a height h, width b, and…

A:

Q: 1- The bearings at A and B exert only y and z components of force on the shaft. If Sy 150 MPa for…

A: Given: The yield strength of material, SY = 150 MPa The shaft diameter, d = 40 mm

Q: The pressure tank shown has an outside diameter of 100 mm and a wall thickness of 10 mm. Determine…

A: Given that do=0.1 m=100 mmt=10mm=0.01 mP=1.25 MPa T= 375 Nm

Q: Bar of steel, (yield strenght Sy = 469 MPa) is subjected to the following stresses; σx = 218 MPa ,…

A: Given data:

Q: The displayed piece is loaded at 300 N with C in the positive x direction and 200 N in the positive…

A:

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.