If the temperature of the 85 mmmmdiameter post CD is increased by 60⚫C, determine the force developed inthe post. The post and the beam aremade of A-36 steel, and the momentof inertia of the beam is | = 255 (106)mm4.Figure1 of 1the temperature of the 85 mm-diameter post CD increased by 60 "C determine the force developed in the post. The post and the beam are made of A-36 meel, and the moment of the255 (30)Express your answer with the appropriate unitsBesUnits

Answered: Image /qna-images/answer/8368c739-fe74-4b7e-bdbc-20711d1bf950.jpg

Answered: If the temperature of the 85 mmmm…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V =4/3 n 13) (E: 125 GPa, v = 0.34, SY = 200 MPa)
Consider the frame shown in (Figure 1). Suppose that w = 410 N/m. Figure 1.5 m y 2m D E 3 m N 3m F 1.5 m B v W 1 of 1 Part A Determine the x and y components of force which the pin A exert on the frame using scalar notation. Express your answers using three significant figures separated by a comma. Ax, Ay = Submit Part B Ba, By = Submit ΑΣΦ Request Answer Determine the x and y components of force which the pin B exert on the frame using scalar notation. Express your answers using three significant figures separated by a comma. < Return to Assignment ΑΣΦ Request Answer ↓↑ vec ↓↑ vec ? Provide Feedback kN ? kN
When a mass of m = 22 kg is hung from the middle of a fixed straight aluminum wire, the wire sags to make an angle of 12° with the horizontal as shown in. The elastic 12° Part A m 12° modulus for aluminum is 7.0 × 10¹0 N/m². Determine the radius of the wire. Express your answer to two significant figures and include the appropriate units.
A shaft is composed of elements made of S355 with a modulus of elasticity of 2.1×1052.1×105 N/mm² and a Poisson's ratio of 0.3. As shown in the picture, on the right side, there are two forces of 10,000 N each, acting at an angle of 15° upwards, creating a moment that is statically compensated by the force F2 on the left side. The shaft is supported at positions A and B. In the same position (for simplicity), there are two critical cross-sections leading to stress concentrations. The sleeve near F2 is shrink-fitted. The dimensions there are d=50 mm, D=120 mm, and the length of the sleeve is 50 mm. Ha=1 µm and Hn=1 µm. The fit is H7/s6. Determine breell.
F=150lb a=6in bd=8in
The structure in Figure Q4 is made of two members, AB and BC, both made of metal with a Young's Modulus E = 110.41 GPa. Member AB has a rectangular cross-section, whose sides measure a = 35 mm, and b = 81 mm. Figure Q4 Calculate the Second Moment of Area of member AB with respect to its strongest orientation. Use π = 3.14159 in your calculations if needed. Express your answer in the unit: mm4. Report your answer to 2 decimal places.
The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. ( Figure 1) The T₁ = 410-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and z components of force on the shaft. Figure X 200 mm 300 mm 150 mm 150 mm 200 mm D 400 mm B 200 N 200 N Z 80 N 80 N 1 of 1 > ▾ Part B ▾ Determine the resultant shear force in the y direction on the cross section at C. Express your answer to three significant figures and include appropriate units. (Vc), = 245.71 ▾ Part C Submit Previous Answers Request Answer * Incorrect; Try Again; 4 attempts remaining Submit (Vc), = Value Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate units. T= HA Submit Part E ריהם Determine the resultant torque on the cross section at C Express your answer to three…
The beam of negligible weight is supported horizontally by two springs. If the beam is horizontal and the springs are unstretched when the load is removed, determine the angle of tilt of the beam when the load is applied. Take x = 659 N/m, y = 1.5 kN/m, and z = 1.6 kN/m.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS