1.5 m B 1.5 m I m 2.5 m 3 m -- 1.5 1.5 m-1 mª| 3 m

Q: Find the external reactions at support A (reverse pendulum) and B (pin) and the reaction of the…

A:

Q: Answer FOUR questions ONLY selecting TWO questions from SECTION A. 1. (a) The vertical structure…

A: Find the reaction at point A and stress in steel bar and aluminium tube.

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A: Draw the free-body diagram of the system.

Q: a=(3.7m) , b=(3.7m) ,theta =(33) , p1=(3.7)KN , p2=(2.4)KN     find the forces in each members…

A: According to the given dataWe need to findforce in each member.

Q: The h = 120 ft tall communication tower is supported by three cables at A and a ball-and-socket…

A: To find: The tension in cable AC and AD along with the force on the tower AO. Given: The tension in…

Q: The bent rod is supported at A, B, and C by journal bearings, as shown in (Figure 1). The rod is…

A: The moment applied is The force applied is

Q: solve  this 3D    RIGID    BODY    EQUILIBRIUM please

A: Step 1: Step 2: Step 3: Step 4:

Q: In the figure the boom derrick supports a suspended 15-kip load . The booms BC and DE are each 20 ft…

A: The question can be solved by applying principles of equilibrium of Forces. Lami's theorem is to be…

Q: The ideal spring of constant k=2.6kN/m is attached to the fitted at point A and the end fitted at…

A: The moment about the z axis of the spring force is .The spring constant is

Q: The member is supported by a pin at A and cable BC. Suppose that r = 3.5 m and the cylinder has a…

A: Consider the free body diagram of the given system as shown below. Here,

Q: For the system shown above, Assume it is fixed at A. 1. Draw a Free Body Diagram. 2. Determine the…

A: According to the given data provided in the question. A loading Aligned beam as provided in the…

Q: 1.5 m B 1.5 m 1m 5 m 3 m 1.5 m1 m* - 3 m

A: Drawing the free body diagram of the given system, Writing the co-ordinates of the point as follows…

Q: The uniform bar with end rollers weighs 60 lb and is supported by the horizontal and vertical…

A: (a) The tension in the wire: T = 60.21 lb. (b) The reactions against the rollers at A and B: NA = 15…

Q: Using the figure below, find (a) the reaction forces at B & C, and (b) the forces in the members AB,…

A: The truss is to be analysed for reactions at supports and for member forces . All the forces are…

Q: consider the rotational axis at the point where the tire contacts the ground, directed perpendicular…

A: A man is pulling a wheelbarrow to lift the weight. A wheelbarrow is a vehicle to lift weight…

Q: A 7-ft boom is held by a ball and socket at A and by two cables EBFand DC; cable EBFpasses around a…

A: Given: The length of boom, L = 7 ft The force acting at C, P = 390 lb

Q: The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents…

A: Given data: A man is pulling a wheelbarrow to lift the weight. A wheelbarrow is a vehicle to lift…

Q: 4/116 The shipboard erane is supporting a load of 4 tons in the position shown where 6- 30°. The…

A:

Q: If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the…

A: Consider the support point O as origin. Thus, the cooridnates of points are, , , and .Write…

Q: The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge…

A:

Q: Refer to Fig. P6–9. Given that the tension T in cable ÀC is 900 N, determ the components of T…

A:

Q: The homogeneous 100-kg sign is suspended from three wires. Find the tension in each wire.

A: Given Mass = 100 kg To find Tension on the strings

Q: 0.3 m B 1.5 m 2 m 0.5 m

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.