4/116 The shipboard erane is supporting a load of 4 tons in the position shown where 6- 30°. The hoisting drum B is operated by a high-torque electric motor. Calculate the added compression P in the hydraulie cylinder and the magnitude R of the additional force supported by the pin at 0, both due to the effect of the 4-ton load. Ans. P = 43,100 lb, R = 35,400 lb 24 A 6" 10" C B 8" D, Problem 4/116

4/116 The shipboard erane is supporting a load of 4 tons in the position shown where 6- 30°. The hoisting drum B is operated by a high-torque electric motor. Calculate the added compression P in the hydraulie cylinder and the magnitude R of the additional force supported by the pin at 0, both due to the effect of the 4-ton load. Ans. P = 43,100 lb, R = 35,400 lb 24 A 6" 10" C B 8" D, Problem 4/116

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

4/6- Frames & Machines / Charpente et Mécanisme Sample Problem / Exemple (4-6) The frame supports the 400-kg load in the manner shown. Neglect the weights of the members compared with the forces induced by the load and compute the horizontal and vertical components of all forces acting on each of the members. ↑ 1.5 m 0.5 m Тв 1.5 m 1.5 m ✓ C A 3 m -2 m E F 0.5 m 400 kg La structure supporte une charge de 400 kg de la façon représentée. Négligez les poids des barres par rapport aux forces développées par la charge et calculez les composantes horizontales et verticales de toutes les forces qui agissent sur chacune des barres.
L from Pivot 1. A uniform bar with mass M =3.25 kilograms is the top end of the bar. A cable connects to the bar as shown in the diagram. the 75.0 40.0° a. Calculate the tension in the cable required to keep tne bar in static equilibrium. Pivot preso your your answe stem right when n terr b. Calculate the force (both magnitude and direction) exerted by the pivot.
3. For the one-dimensional 4 truss-element system shown, determine the nodal displacements and reaction forces using the direct stiffness method. K3=45 lb/in for F=75 lbs KI=25 lb/in K2=35 lb/in K=30 lb/in
Calculate the tension T in the cable which supports the 1000-lb load with the pulley arrangement shown. Each pulley is free to rotate about its bearing, and the weights of all parts are small compared with the load. Find the magni- tude of the total force on the bearing of pulley C. 8=30° Joel 1000 lb
Need help. Please solve this and clearly state how you got your numbers and what formulas you used to solve it. Please make sure you find all the 6 unknows please. Knowing the beta equals 30° and the solid plate weigh 100 kg. What is the cable tension T and the reaction forces at the two bearings? Assume bearing A is a thrust bearing but bearing B is notplease solve for the X component at bearing B. Again please also make you find all the 6 unknows please. And clearly indicate which is which. And please label and make sure to put units
3. The image below depicts a truss structure used to lift Mini Cooper S Roadsters. As can be seen the weight of the vehicle (2,800 lb.) is attached to the structure at joint D and directed in the negative z-direction. The coordinates for the joints (assumed to be of the ball and socket type) can be found in the table below. Determine the forces in each truss member by developing a system of linear equations and using the solve command in Sage to find the solution. - HINT: Isolate joint D and draw a free body diagram. By summing the forces in the x, y, and z directions you will obtain a linear system of three equations and three unknowns. Joint Location (0,-2,5) (0,3,5) (0,0,0) (6,0,4) OF хX
1. For the one-dimensional 3 truss-element system shown, determine the nodal displacements and reaction forces using the direct stiffness method. K2 = 60 lb/in KI= 50 lb/in K3 = 55 lb/in Node 4 F = 60 lbs. Node 3 Node 1 Node 2 +X 2. For the one-dimensional 4 truss-element system shown, determine the nodal displacements and reaction forces using the direct stiffness method. K2=35 lb/in F=80 lbs Kı=35 lb/in K3=25 lb/in K4=30 Ib/in +X 3. For the one-dimensional 4 truss-element system shown, determine the nodal displacements and reaction forces using the direct stiffness method. K3=45 lb/in F=75 lbs KI=25 lb/in K2=35 lb/in K=30 lb/in to +X
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 42 45 100 Ib 18 3 ft 3 ft- 30 200 Ib ft 30" 30 30 kg 2 ft B B Fig (1) Fig (2) Fig (3)
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
4m 6 - The cable from A to B is 6 m long and supports the 100-kg crate from the small pulley Calculate the tension T in the cable . 100 kg
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 20i - 14j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Quiz 2. 9, 2 m 17 4 m Finish Time lI 6 m 曲