For the material indicated determine the required diameter of the rod.

Q: For the pair of 26-lb forces applied to the handles of the crimper tool, determine the crimping…

A:

Q: If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on…

A: Given data: FS=2.2σfail=614  MPa Need to determine the allowable stress for member σallow.

Q: A gear motor can develop 5 hp when it turns at 200 rpm. If the allowable shear stress for the shaft…

A:

Q: One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 289.5 MPa,…

A: Given data: Shear stress at point A = SA = 269.5 MPa Radius of point A = rA = 40 mm = 0.04 m Shear…

Q: 6. Way 28 mm diameter steel and 20 mm A composite beam made of aluminum rods in diameter. Elasticity…

A:

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Show the force and moments on cross section H.

Q: The lap joint is fastened with four 0.52-in-diameter rivets. The working stress is 19.7 ksi for the…

A: Given Data The diameter of the rivet is: d=0.52 in The working stress is: σw=19.7 ksi=19700 psi The…

Q: The triple thread screw has a lead of 15 mm. Determine its thread per inch.

A: Given               Lead, L = 15 mm                           = 0.59 in No of thread, n = 3 Find…

Q: Determine the vertical displacement of point B. Each A-36 steel member has a cross- sectional area…

A: Given,A = 400 mm2E = 200 GPa

Q: A thin spherical shell 1 m in diameter with its wall of 12 mm thickness is filled with a fluid at…

A: D= 1m t= 12mm E= 200 GPaμ=.3Lets assume volume of fluid pump δv=175 cm3δv=175×10-6 m3Now…

Q: 13.Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it…

A:

Q: SIMPLE STRESSES 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable…

A:

Q: A structural member is said to be slender when the dimensions of its cross section are its length O…

A: A structural member is said to be slender when the dimensions of its cross section are............…

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: Consider the cross-section of the beam, Calculate the centroid of the section,…

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: 2. Determine Ig-g for the T-section shown. | 40mm 209.545mm 250 mm g 100.455mm 60 mm 200 mm

A:

Q: The loads illustrated produce concentric axial force in the 20-mm-diameter shaft, which is made of…

A:

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A higher polar moment of inertia means that the specimen needs a lower angle of twist to be failed.…

A: The angular deflection of the specimen is given by - θ=TLGIP⇒T=GIPLθwhere T= Twisting Moment ,…

Q: Find the section modulus of shaft having 2.5 in diameter. A 3.07 in B. 4.56 in C 5.45 in D. 8.46 in

A: Given data : Shaft of 2.5 in diameter Diameter of shaft=d   Required : Section modulus

Q: bearing plate 15⁰ 20⁰ 25⁰ Cross- sectional Area

A:

Q: A cylindrical rod .5" in diameter is subjected to an axial load of 11,300 lbs. A square bar of .5"…

A:

Q: The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for…

A:

Q: F E 3 ft A C В 4 ft 4 ft 800 lb

A:

Q: A 400-mm-long rod with a diameter of 4.5 mm is loaded with a 5000-N weight. If the diameter…

A:

Q: 1-90. A steel rectangular tube has outside dimensions of 150 mm x 50 mm and a wall thickness of 4…

A: Inside dimensions of tube

Q: Compute the resultant force acting on the pin at C (In kN).

A:

Q: Note: End of the question answer also given if you got answer other than that values please leave…

A:

Q: Need help asap Find the force (N) in link if θ= 0° and P = 295 N. Round off only on the final…

A:

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: Compute the resultant force acting on the pin at C (in kN). 7- 1,800.00 mm kN 30 kN Enter 2,150.00…

A:

Q: A thick-walled pipe should be mounted in the space between a shaft and a wreath....

A: Given-Data:- Inner Radius =aOuter Radius =2av=1/2 To-Find:- Tension

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: Draw the diagrams for all the sections views, using the dotted outlines as a guide. Assume that the…

A: Draw the diagrams for all the sections views, using the dotted outlines as a guide.

Q: The bar is made from welding two uniform 40 lb bars together. Calculate the magnitude of the pin…

A:

Q: Determine the force acting on members DE, DC, BC in an inverted roof truss as shown below. Use…

A: Given data  Given truss system.

Q: Determine the vertical displacement of joint C . EA is constant

A: The vertical displacement of the joint C. FBD: The free-body diagram of the joint C is shown below.

Q: A 102 mm diameter shaft is driven at 3000 rpm by a 250 Hp motor. The shaft drives a 121.9 cm…

A:

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.