Compute the resultant force acting on the pin at C (in kN). 450.00 mm 55 kN kN 450.00 mm Enter 15 kN 450.00 mm C 800.00 mm

Q: For the pair of 26-lb forces applied to the handles of the crimper tool, determine the crimping…

A:

Q: 7.ON 5.0N 15 20 50 4.0N

A: To calculate the resultant force of the given system first determine the component of forces in x…

Q: The resultant couple moment acting on the triangular block is to be zero. (Figure 1) Take F₁ = 15…

A:

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: To findDraw the loading diagram showing the internal forces and moment/Torque acting on a cut…

Q: 1.25 kN 220 300 Bearings at B and C act as simple supports A 300 550 Dimensions in mm

A:

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: SOLVE FOR THE RESULTANT OF THE 300N AND 100N FORCE. (NOTE: ALSO CALCULATE THETA

A:

Q: Determine the stress area in mm2 of a 1.75 - 8UNC bolt.

A:

Q: 1- Determine the resultant of the forces which shown in figure pila a F= 300 lb F-150 lb 37 55 13 Fy…

A:

Q: Free body diagram required. Use paper sheet to solve

A: thank you

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: 03: For the cyclic stress shown in the figure (aside) calculate: 1. The mean stress 2. The range of…

A:

Q: I 10'- 50° F E -10'- -10'- G 8' H D A 2 kips 20° 4 kips 4 kips 2 kips

A:

Q: 2 B

A: To-Find:- Resultant at point C

Q: Q2/compute the moment of force 650 N about the rod AB. 125 mm 150 m 150 m 100 mi 30

A:

Q: Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin…

A:

Q: 6.) The system of knotted cords shown in the figure supports the indicated weights. Compute the…

A:

Q: All three cables pull down at D. The forces in cables DA and DB are equal and the force in cable DC…

A:

Q: Q1: Calculate the moment of the 0.4 kN force about point O. A et Ww a ana Va y nor de faliatea hanc…

A: Given Data P=0.4 kN

Q: F E 3 ft A C В 4 ft 4 ft 800 lb

A:

Q: Compute the 1. force in each member. 2000 lb 3000 1b

A:

Q: Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin…

A:

Q: 8 kN/m Refer to figure 19, Calculate the magnitude and 4 kN/m position of the resultant load from…

A: Draw the free-body diagram of the beam.

Q: Fill in all blanks before submission. Round the answer to the nearest integer. The post shown below…

A: Apply Equilibrium Conditions

Q: Replace the force system by an equivalent resultant force and couple moment at point O (Figure 1).…

A: Given data:- F1= 24 lb F2=24 lb To find:- Resultant of force Angle of resultant Moment about point…

Q: Compute the resultant force acting on the pin at C (In kN).

A:

Q: Need help asap Find the force (N) in link if θ= 0° and P = 295 N. Round off only on the final…

A:

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: a) Determine the force Få acting at roller D. b) Determine the force FE acting at pin E. F

A: In the equilibrium rigid structure net force in the x direction, and y direction is zero and the net…

Q: Q// Determine the resultant force in figure bellow, and specify where it acts measured from point B.…

A:

Q: Compute the resultant force acting on the pin at C (in kN). 7- 1,800.00 mm kN 30 kN Enter 2,150.00…

A:

Q: Q2/compute the moment of force 650 N about the rod AB. 125 mm 150 mm 150 mm 100 m 300man-

A:

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: What is the Share Force (in KN) at a point 0.6L (where L is the length of the plank) given that: F1…

A:

Q: The crane arm in the figure lifts the 95 kg mass at the end. When the angle BC piston makes with the…

A:

Q: resultant force and couple moment at point A. (Figure 1) Take F₁ = 300 lb, F₂ = 420 lb, and F3 = 3…

A: Given data F1 = 170 lb F2 = 210 lb F3 = 160 lb Find the magnitude of resultant force and angle with…

Q: -61.M Figure P1-61 shows the shape of a slug from a sheet of aluminum 5.0 mm thick shear stress in…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.