1-61.M Figure P1-61 shows the shape of a slug to be punchedfrom a sheet of aluminum 5.0 mm thick. Compute theshear stress in the aluminum if a punching force of38.6 kN is applied.43 mm35 mm-8 mm

Answered: Image /qna-images/answer/a3ea6b5e-dd0c-470c-b1fa-9d8e6354e9f9.jpg

Answered: -61.M Figure P1-61 shows the shape of a…

-61.M Figure P1-61 shows the shape of a slug from a sheet of aluminum 5.0 mm thick shear stress in the aluminum if a punc 38.6 kN is applied. 43 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q16/ The value of the normal stress due to :axial force 2 kN applied on the beam is Point D 10 kN…

A: For this question, Axial force = P = 2 kN = 2000 N Cross section of the beam = 200 mm x 100 mm We…

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

Q: 1-69.M Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be if the…

A: Given:Tensile load, P = 22.3 kN or 22300 NDiameter of circular shank, d = 12 mmHeight of the head, h…

Q: pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE…

Q: Pa. Construct the Mohr's circles

A: The stress state at a point of a machine element is give by.

Q: T3-at 2.5 in. above the NA (at the top of the web) = ksi T4 at 1.25 in. above the NA = T5 at the NA…

A: The dimension are The shear force is

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

Q: Determine the normal stress that acts at point B.

A: The rod diameter d =40 mm = 0.04m The force system Fx= 1390N Fy= 510N Fz= 835N Find a) The Normal…

Q: Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze 83…

Q: 60mm 2. H we measure a &=13µm decrease in the bolt diameter d. Bolt material properties are given as…

Q: The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If…

Q: Consider the plates shown in (Figure 1). Take P18 kip and P₂ -9 kip. Determine the maximum average…

Q: The stress strain curve determined from a sample of material is shown in the figure. The original…

Q: 20 mm- 50 mm 20 mm 100 mm 50 mm 100 mm M-8 kN-m A unique strut, shown in the figure, will be used in…

Q: Question 2 At a given point in a machine component, the following stresses were determined: 150 MPa…

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: Determine the diameter of the bolts if the stress in bolt 1 is 200Mpa. Note: Distances are in mm.

A: The information provided in the image, it is not possible to directly determine the diameter of the…

Q: It is used to find the shear strength of a 3-system material. T-shaped test is used for this. When…

A: Given: t = 4mm Ultimate load is 9 kN.

Q: (1) Given: b₁ B P=28 kN Square Bars b₁ = 57mm Q = 9 kN C b₂ = 19mm (3) Q R = 38kN b3 b3 ↑ D = 38mm R…

A: given; p=28KNQ=9KNR=38KNb1=57mmb2=19mmb3=38mmaxial stress in bar 2 (σ2)=?

Q: The plate shown in the figure is fastened to the fix by three 10mm diameter rivets. Compute the…

Q: b=3./m a=2.1m (1) B C = 2m (2) P = 80kN C d = 1.8m WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

Q: erial when longitudinal strain is 0.12mm/mm and transverse strain is -0.03

A: Given data Longitudinal strain=0.12mm/mm Transverse strain=-0.0396mm/mm

Q: The plastic pipe AC has a hollow circular cross- section as shown to the right. Determine the normal…

Q: ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

Q: 1.61.The state of stress at a point relative to an x, y, z coordinate system is given by 12 4 -8 1…

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: In the figure, when the torture squeezes the material, the maximum force F in the clamping jaws is…

Q: B 20 mm- 50 mm 20 mm 100 mm 50 mm 100 mm M = 8 kN-m

Q: Please solve in detail. Don't use chatgpt,The Free body diagram must be drawn.

A: Free-body Diagram: Note: I hope this helps. Thank you.

Q: (1) Given: P=28 kN b₁ B Square Bars b₁ = 57 mm P Q =9 kN (3) Q R = 38 kN b₂ = 19mm b3 ↑ D = 38mm R…

Q: If the principle stresses in a plane stress problem are 100 MPa and 40 MPa, then maximum shear…

A: As given in the question, Maximum principal stress = σ1 = 100 MPa Minimum principal stress = σ2 = 40…

Q: n the figure as shwon: Member AB and BC are made of the same material. it was tested that the same…

A: Given:For the material:F=12 kNArea, A=25 mm2

Q: Determine the smallest yield stress for steel that might be selected for the part, based on the…

A: Given data,the state of stressFind outthe smallest yield stress for steel using the maximum shear…

Q: The stress strain curve determined from a sample of material is shown in the figure. The original…

A: The original diameter isThe final diameter is The load applied is

Q: Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear…

Q: 4. An unknown metal cube measures 3.5 x 10 -2m decreases a volume of 5.8 x 10 -8m ³. At what stress…

Q: Onv Problems 9-29 to 9-32 F 9-29 to 9-32 A steel bar of thickness h is welded to a vertical support…

Q: Using Vector Algebra, a. determine the magnitude of F that will cause the net effect of the three…

A: Given:Forces on the bolt:F1=FF2=410 NF3=200 NDiameter of the bolt, d=3/8 in

Q: (1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm VIO (3) Q R = 38kN b3 b3 ↑…

Q: (YC)zy = Submit Part B Value (YD)zy = Request Answer Determine the shear strain Yzy at corner D.…

Q: When they go to calculate both the normal stress of the bolt and the shear stress for the supporting…

A: Step 1:Step 2: Step 3: Step 4:

Question

1-61.M Figure P1-61 shows the shape of a slug to be punched
from a sheet of aluminum 5.0 mm thick. Compute the
shear stress in the aluminum if a punching force of
38.6 kN is applied.
43 mm
35 mm
-8 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data with suitable variables-

VIEW

Step 2: Determine the value of shear stress-

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

It is really confusing question ,Please attempt only if you are 100% Sure .
PLEASE ANSWER NUMBER 4
10/10 find the tensile stress in upper plate in section 3-3 5. 1 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 2) 300 mm 8 mm
Three solid cylindrical are welded together as shown in Figure 3. Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure. 50 mm 25 mm 25 mm B. 15 kN A 40 kN 30 kN C 10 kN Figure 3
Only handwritten and correct pls
Question 2 The steel bar has the dimensions shown in Figure 2 below. Determine the maximum axial force P that can be applied if the ultimate normal stress for the steel is 215 MPa and the factor of safety 2.0 is desired. / 3.4 3.2 3.0 2.5 2.4 K 2.2 2.0 1.8 1.6 1.2 1.0 0 0.1 02 (a) Flat bars with holes P. 30 mm 24 mm- 20 mm 60 mm Figure 2 03 04 05 06 07 2r/D 3.2 3.0 2.5 26 K 22 20 1.8 1.6 1.4 12 1.0 r = 15 mm (b) Flat bars with fillets D Did-2 13 13 12 000204000005 0.10 0.12 0.34 0.30 0.15 0.20 0.22 0.24 0.28 0.25 6.30 vid Figure 3: Stress Concentration Factor, K for the Flat Bars
Part A The lever is attached to the shaft A using a key that has a width d and length of 26 mm .If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the key is T = 37 MPa (Figure 1) Express your answer with the appropriate units. HA d = Value mm Submit Request Answer Provide Feedback Next > Figure d -20 mm 500 mm 200 N
Question 1 Two circular rods of 50 mm diameter are connected by a knuckle joint, as shown in Figure 1, by a pin of 40 mm in diameter. If a pull of 120 kN acts at each end, find the tensile stress in the rod and shear stress in the pin. 50 x 11.00 in Rod (1) Pin Rod (2)
PLEASE ANSWER IT CORRECT I WILL UPVOTE AFTER
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. A parameter value units 470 mm 400 mm 40 mm 30 mm 30 KN cc 080 BY NO SA 2021 Cathy Zupke L₁ L2 d₁ d₂ P 4₁ B C E The stress in AB σAB= The stress in CD and EF: OCD = EF= d₂ L₂ MPa D F MPa
1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1. P- 10000 Ib 4 in
a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B dia. of rod 1: = 13mm dia of rod 2 = 11 mm