The turbine develops 230 kW of power, which is transmitted to the gears such that both B and C receive an equal amount. The rotation of the 100-mm-diameter A992 steel shaft is w = 720 rev/min. (Figure 1) The journal bearing at D allows the shaft to turn freely about its axis. Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate i µA ? 'max Value Units

The turbine develops 230 kW of power, which is transmitted to the gears such that both B and C receive an equal amount. The rotation of the 100-mm-diameter A992 steel shaft is w = 720 rev/min. (Figure 1) The journal bearing at D allows the shaft to turn freely about its axis. Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate i µA ? 'max Value Units

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
6. I upvote! Thanks!
I need answer within 5 minutes please please with my best wishes
Only HAndwritten answer please
A torque of TD= 1235 N-m is applied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely. Assume shafts (1) and (2) are solid 26-mm-diameter steel shafts. Determine the magnitude of the maximum shear stress acting in shaft (2). 230-mm dia. TD C B 150-mm dia. O 357.9 MPa O 449.0 MPa O 415.7 MPa O 217.5 MPa O 391.8 MPa
Quickly please
A 3 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 200 HP. The shaft speed is 1500 rpm. The allowable shear stress is 40 ksi and the allowable angle of twist per foot of length is 0.05 radians. Determine the minimum diameter that meets the design requirements. Note: Shear modulus for steel is given in Appendix 3/ Page 788.
The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig.The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c. use G=80 Gpa 150 N.m 280 N.m c 40 N.m 0.4m 0.3m
Mechanics of deformable bodies
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure 4. Take G = 75 GN/m². (i) (ii) Determine the location along the 40 mm diameter shaft where the shear stress is largest and plot the variation in shear stress from the shaft centre to its outer surface. Determine the angle of twist of sections C, D, and B relative to end A by producing a graphical plot of the variation of angle of twist from end A to end B (wind-up diagram). 300 N-m 500 N-m A www. 300 mm 200 N.m MAAN 400 mm Figure 4 500 mm 400 N-m
Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor machine tools connected to gears F and G. Assuming that, 10 kW is taken off at gear F and 20 k taken off at gear G, knowing that allowable torsional shear stress is equal to (65 plus last digit of student ID) MPa. Design the smallest permissible diameter of shaft AB. Figure 1 150 mm 225 mm 905 mm 150 mm 60 mm 100 mm D. 60 mm B.