1- The bearings at A and B exert only y and z components of force on the shaft. If Sy 150 MPa for the selected ductile material, determine the factor of safety if the shaft diameter is 40 mm. Use the maximum distortion-energy theory of failure. Show the following procedures through the calculation steps (Free Body diagram (FBD), Reaction at A and D, Bending moment diagram, point of max. moment, Torque diagram, draw the element showing general stress (ox, Txy), the factor of safety using the MDE. 500 N 100 mm 150 mm 200 mm 150 mm -100 mm 500 N

1- The bearings at A and B exert only y and z components of force on the shaft. If Sy 150 MPa for the selected ductile material, determine the factor of safety if the shaft diameter is 40 mm. Use the maximum distortion-energy theory of failure. Show the following procedures through the calculation steps (Free Body diagram (FBD), Reaction at A and D, Bending moment diagram, point of max. moment, Torque diagram, draw the element showing general stress (ox, Txy), the factor of safety using the MDE. 500 N 100 mm 150 mm 200 mm 150 mm -100 mm 500 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 25-mm-diameter 2014-T6 aluminum rod is subjected to the uniform distributed axial load. Take E = 73.1 GPa. (Figure 1) Part A Determine the displacement of end A. Express your answer to three significant figures and include the appropriate units. ? 8A = 0.27 mm Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Figure < 1 of 1 Provide Feedback -30 kN/m 900 mm
Find the shaft diameter and the factor of safety against yielding
Use the von Mises failure criterion to solve for the minimum required yield stress if a factor of safety of 2 is needed and the applied state of plane stress is as given below. Give your answer as an integer in units of MPa (e.g. 200 or 200MPA) +100MP. |3D oy = -78MP. Try +30MP.
Please solve this question carefully and circle the final answer with the correct units use the image below
The shaft is supported by journal bearings at A and B that exert force components only in the x and z directions. Part A d= PLÅ Value Ĵ t O Determine the smallest diameter of the shaft. Use the maximum shear stress theory of failure with Tallow Express your answer to three significant figures and include appropriate units. Units HATT F = 200 lb ? X 8 in. 1 4 in. 8 in. N A 8 ksi 4 in. D F. = 50 lb 8 in. 4 in. F = 250 lb 4 in. SE B y
solve neatly
Please I want answer of that question from these choices
4. A beam has fluctuating bending moment and is not rotating. The bending moment has a maximum of 1kNm and a minimum of 100kNm. The beam is made of AISI1020CD steel with a square cross section. There are no stress concentrations. a. Determine the fully corrected endurance limit as a function of the cross section (cross section unknown) b. Determine the required size for a factor of safety of 2 using the Gerber Fatigue Failure Theory
42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
The rotating shaft in the given figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 6 kN. Find the minimum factor of safety for fatigue based on infinite life. Be sure to check for yielding. 500 F -175- 25 D. 35 D. 3 R. -50 D. 25 D. Dimensions in millimeters -20 -20 280- -20 20 -180 Determine the endurance limit for this material as well as the value after correction for surface finish, sizing, and loading. The endurance limit for this material is MPa. The endurance limit after correction is MPa.
Dr. (ny) A = 5.52 تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy === Sy (Neglect buckling) 600 kN 30 T 100 mm 600 kN Prepared by Dr. Hazim Khale anc dir the dia BC (b to ca th th n
30 min. Q4 (DÖÇ-1) For the given gear-shaft system failure shear stress for the shafts is 90 MPa, If the factor of safety is 1.5 and the diameter of the shaft CD is d2 = 60 mm, determine the minimum diameter of shaft AB, d,. Shafts turn freely within the bearings. rg = 150 mm, rc = 100 mm B