Needs Complete typed solution with 100 % accuracy. The assembly consists of two 12-mm-diameter A992 steel rods ABand CD, a 20-mm-diameter 6061-T6 aluminum rod EF, and a rigidbar AEC (Figure 1)FigureF600 mm 12P2PEC400 mmBD< 1 of 1 >Part AIf P = 35 kN, determine the displacement of FExpress your answer to three significant figures and include appropriate units.Sp= 0.223μAmmSubmit Previous Answers Request AnswerProvide FeedbackX Incorrect; Try Again; 3 attempts remaining

To determine:The displacement of point Fgiven:The diameter of rods AB and CD is The diameter of rod…

The assembly consists of two 12-mm-diameter A992 steel rods AB and CD, a 20-mm-diameter 6061-T6 aluminum rod EF, and a rigid bar AEC (Eigure 1) Figure 600 mm 2.P 2P 400 mm B < 1 of 1 If P = 35 kN, determine the displacement of F Express your answer to three significant figures and include appropriate units. O Submit Sp = 0.223 I Provide Feedback μA mm Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining

The assembly consists of two 12-mm-diameter A992 steel rods AB and CD, a 20-mm-diameter 6061-T6 aluminum rod EF, and a rigid bar AEC (Eigure 1) Figure 600 mm 2.P 2P 400 mm B < 1 of 1 If P = 35 kN, determine the displacement of F Express your answer to three significant figures and include appropriate units. O Submit Sp = 0.223 I Provide Feedback μA mm Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.31P

See similar textbooks

Similar questions

What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application requires a factor of 0.34 for the type of service. Round your answer to 4 significant figures.
Consider the toggle clamp shown in (Figure 1). Figure -235 mm- 30 mm 70 mm 30 mm D 30 30 E Part A If a clamping force of 350 N is required at A, determine the magnitude of force F that must be applied to the handle of the toggle clamp. Express your answer to three significant figures and include the appropriate units. F = - 1370 Submit μÃ Provide Feedback ^ X Incorrect; Try Again + N • 5) ? Previous Answers Request Answer Next >
asap
After recording the applied twisting moment and resulted angle, fill the following table MT (N.m) T. MPa (degree) (rad.) Now, the twisting moment-twisting angle and shear stress-shear strain curves can be plotted, then determine maximum shear stress, shear stress at proportional limit and modulus of rigidity. 4-6 Problem The following torsion test data were obtained for AA6061-T6 aluminum alloy has a round cross section with 30mm outer diameter, 0 inner diameter and 100 length. 0 32 130 Twisted angle (): 0 1 Torque (N.m): 286 347 487 5.5 591 786 910 1105 1163 1235 1222 3.5 6.5 7.5 9. 10.5 13.5 16.5 21.5 25.5 > Plot the torque-twisted angle curve and determine the proportional limit on it. Plot the shear stress-strain curve the determine the shearing strength and modulus of rigidity. Prof. Adnan N. Abood Asst. Lec. Zainah Waheed 25
Required information Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. Given: P₁ = 65 kN and P2 = 40 kN. Take Es = 200 GPa and Eb = 105 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -180- Dimensions in mum Steel B 120- P₁ 40-mm diam. 100 100 DI C Brass 30-mm diam. Determine the reactions at A and E. The reaction at A is The reaction at Eis P2 E KN (Click to select) ✓ KN (Click to select)
F1=603N F2 =818N show a detailed solution please
L21. Figure P4-21 shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is to be 500 lb, specify a suitable diameter for the steel pin if it is to be made from SAE 1040 WQT 900. 4-21
In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.
The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
3:35 PM Wed Dec 15 7 51% A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a suitable diameter for the solid circular shaft if it is to be made from AISI 1020 cold-drawn steel. Use Appendix A-2 for preferred size. 61
Part A Consider the mechanism shown in (Figure 1). FA = Submit 0 ■ μÅ -235 mm Value 30 mm 30 mm/ If a force of F = 350 N is applied to the handle of the toggle clamp, determine the resulting clamping force at A. Express your answer to three significant figures and include the appropriate units. 70 mm Request Answer B 30 Units F 30% 275 mm ] ?
The Steel Wheel on The Steel Rail. Flange- Wheel Axle Tie Rail