2.10. Compute the long-term average throughput, cycle time and x-factors for this factory for fixed WIP levels of 1 through 5 for the four machine serial flow factory model below where the constant processing times are listed on the machines. As- sume that the factory starts with the configuration (N,0,0,0) for fixed WIP level N and no processing has occurred on any of the active jobs. out 2 2 3 2 new

2.10. Compute the long-term average throughput, cycle time and x-factors for this factory for fixed WIP levels of 1 through 5 for the four machine serial flow factory model below where the constant processing times are listed on the machines. As- sume that the factory starts with the configuration (N,0,0,0) for fixed WIP level N and no processing has occurred on any of the active jobs. out 2 2 3 2 new

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Perform the following integrations: Show complete, correct and organized solutions:
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
answer with complete solution
I need the answer as soon as possible
For a unity negative feedback control system having an open-loop transfer function, G(s) as given below. Find out the value of "K" such that the system will be in the stable region. (K/s) (s3 + 12. 5s2 + 50. 5s + 66) G(s) =
Give a physical example for feedback control systems. Sketch the block diagram with input and output variables: Missile launch system
For the system represented by the following block diagram, Find a) The Closed-loop Transfer function. b) Characteristic equation. c) Type and Order of the system. c) Time-domain Specifications ( Delay Time, Peak Time, Rise Time, Settling time, and Percentage overshoot). R(s) C(s) G(s) H(s) Where G(s) and H(s) are given as : 324 G(s) = s(s+6) H(S) : 1
Please solve this question in mechatronics
2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
ques 2 plz provide step by step answer for this question asap dont copy
Hand written plzzz...i'll give you multiple upvote..asap...
Consider the basic EOQ model. We want to know the sensitivity of (1) the optimal order quantity, (2) the sum of the annual order cost and the annual holding cost (not including the annual purchase cost cD), and(3) the time between orders to various parameters of the problem. a. How do (1), (2), and (3) change if the setup cost K decreases by 10%? b. How do (1), (2), and (3) change if the annual demand doubles? c. How do (1), (2), and (3) change if the cost of capital increases by 10%? (For this part, assume that the storage cost s is zero.) d. How do (1), (2), and (3) change if the changes in parts a, b, and c all occur simultaneously?