F₁ = 14 kN a= 270mm, b= 160mm, c= 80mm, and = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 30 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 1 decimal place Bell crank Support bracket a b

F₁ = 14 kN a= 270mm, b= 160mm, c= 80mm, and = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 30 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 1 decimal place Bell crank Support bracket a b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 510-kg engine is suspended from the jib crane at the position shown. (Figure 1) Figure 2m 2 m 2 m 430 D a 0.4 m 150 mm T 150 mm 20 mm- A 20 mm + T 300 mm 20 mm Section a-a 1 of 1 Part A Determine the normal stress at point A on the cross section of the boom at section a - a. Express your answer using three significant figures and include the appropriate units A= -3.327 Submit Previous Answers Request Answer Part B HÅ ^ * Incorrect; Try Again; 5 attempts remaining TA = Submit Determine the shear stress at point A. Express your answer to three significant figures and include the appropriate units. D Provide Feedback MPa μA Value Request Answer ? Units BE ?
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.26-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5205 lb. Round off the final answer to two decimal places.
The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.
The 520-kg engine is suspended from the jib crane at the position shown. Determine the state of stress at point B on the cross section of the boom at section a -a. Point B is just above the bottom flange. (Figure 1) Figure 2m 2m 2m- 4 MP A D 0.4 m 150 mm 150 mm . Determine the normal stress at point B Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. Submit μA B = 3.85 Units You have already submitted this answer. Enter a new answer No credit lost. Try again. TB = n → Previous Answers Request Answer Submit Determine the shear stress at point B. Express your answer to three significant figures and include the appropriate units. HA ? Value Request Answer Ć Units P ?
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5 kN. The crankshaft dimensions are b1 = 80 mm, b2 = 135 mm, and b3 = 55 mm. The diameter of the upper shaft is d = 26 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. | Yo B b3 Lütfen birini seçin: a. -155.971 MPa b. -200.302 MPa c. None d. -520.946 MPa e. -124.141 MPa
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1.5 kN. The crankshaft dimensions are b1 = 55 mm, b2 = 150 mm, and b3 = 45 mm. The diameter of the upper shaft is d = 22 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. | Yo by bz Lütfen birini seçin: a. -302.704 MPa b. -155.971 MPa c. None d. -200.302 MPa e. -147.437 MPa
The bell-crank mechanism is in equilibrium for an applied load of F1 = 17 kN applied at A. Assume a = 290mm, b = 120mm, c = 80mm, and e = 35°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 36 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F2 Support bracket A a Answers: Tpin B = MPa Ob = i MPa
Solve the problems below: 1. The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 20 mm and an inner diameter of 18 mm, whereas the larger pipe has an outer diameter of 25 mm and an inner diameter of 20 mm. If the pipe is tightly secured to the wall at C, determine the maximum shear stress developed in eah section of the pipe when the couple shown is applied to the handles of the wrench. B 75 N 150 mm 200 mm 75 N
The 53kg girl shown is doing a chin-up. For the position shown, the humerous is modelled as an axially loaded member. Determine the normal stress (in MPa) at section a-a if the section is modelled as a hollow cylinder of outside diameter 22.4mm and inside diameter 15.2mm. Note: Do NOT include units in your answer a-+-a (а) (b) Answer:
5. The hanger is supported using the rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is b,allow = 220 MPa, the allowable tensile stress is at,allow = 150 MPa, and the allowable shear stress is Tallow = 130 MPa. Take t = 6 mm, a = 5 mm and b = 25 mm. 75 mm 37.5 mm 20 mm 10 mm 37.5 mm
The pin support A and roller support B of the bridge truss are supported on concrete abutments. If the allowable bearing stress of the concrete is oallow = 2 ksi, determine the required minimum dimension of the square bearing plates at C and D to the nearest 1/16 in. 150 kip 100 kip B 200 kip 300 kip 300 kip 300 kip 300 kip -6 ft --6 ft--6 ft--6 ft--6 ft--6 ft-