EXERCISE Design a combinational circuit by using a 4x1 multiplexer (Mux-4 wo/EN) with three inputs A, B, C and one output Y. The output is one when binary value of the input is less than three. The output is zero otherwise. a. Fill the truth table in table 3 for the given function and determine output Y in terms of C. Table 3 INPUTS OUTPUT B C 0 0 0 1 A Y 1 1 1 1 0 0 1 1 1 1 1 1 1 b. Design the circuit with a 4x1 multiplexer (if needed NOT gate can be used). DEV2 S1 so c. Implement your design by LogicWorks5. Verify the truth table obtained in part a and show your design to your instructor.

EXERCISE Design a combinational circuit by using a 4x1 multiplexer (Mux-4 wo/EN) with three inputs A, B, C and one output Y. The output is one when binary value of the input is less than three. The output is zero otherwise. a. Fill the truth table in table 3 for the given function and determine output Y in terms of C. Table 3 INPUTS OUTPUT B C 0 0 0 1 A Y 1 1 1 1 0 0 1 1 1 1 1 1 1 b. Design the circuit with a 4x1 multiplexer (if needed NOT gate can be used). DEV2 S1 so c. Implement your design by LogicWorks5. Verify the truth table obtained in part a and show your design to your instructor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please solve it using Digital logic
Asap please with proper explanation
응 Question 5: You have a 4-bit data input into your circuit. Your inputs are the data bits d3...d0, where d3 is the MSB and d0 is the LSB. You plan to design a circuit that tells you if the number is greater than 6 (BLUE LED is ON), You also want to know if the number is less than 9 (GREEN LED is ON). Clearly, if the number is in between, both LEDS can be ON. a) Draw the truth table for both LEDS (output). Call the outputs G, B. b) Draw 2 K-Maps for your G, B LEDS. Do not simplify. c) Simplify both K-Maps and write Boolean expression for G = f(d0, d1, d2, d3) B = f(d0,d1, d2, d3) 00 01 'p'p 11 °p'p Ow 00 01 10 m2 m14 m10 9m, d3 d2 d1 BLUE (B) GREEN (G) OP
Explain whats going on SIMPLY!
Design a JKFF by using only a DFF and logic gates. Please design on logisim or handwriting
DIGITAL SYSTEMS - (logic gates) Please can you solve this question by simplifying the circuit in the simplest possible form. Thank you.
I want to perform addition of the following two binary numbers A and B using a combination of Full adders and Half adders. A3 A2 A1 A0 + B3 B2 B1 B0 where A0 and B0 are LSBS and A3 and B3 are MSBS. Then to add which pair of bits would you use a Half Adder? O a. A1 and B1 O b. A3 and B3 Oc. A2 and B2 O d. A0 and BO
From the following truth table, construct a kmap (sop) and design the combinational logic circuit using 4:1 Multiplexer
Electrical Engineering please try all questions. thank you so much (8086/8088 assembly programming) (4a) A program is written to add the values 1000H, 2000H, 00FFH, and 1111H. The partially completed code segment is given below. Complete the partially completed code given below. The final result should be stored in DX. 81 CSEG SEGMENT 82 START: 83 04 MOU AX, 1800H MOU BX, 2000H MOU CX, 08FFH MOU DX, 1111H 85 86 87 08 ; WRITE YOUR CODE HERE 89 10 11 ; return control to DOS MOU AX, 4C00H INT 21H 12 13 ENDS (4b) Write an instruction sequence to implement (08H+16H)/2. Hint: The division by 2 can be accomplished by right shifting the value by 1 bit. (4c) An assembly program is given below. 81 DATA SEGMENT DB 179 02 BINUAL 83 MSG DB This is final exam!' 84 DB ODH, BAH,'$' 05 VAR1 EQU 9983H 86 VAR2 EQU 67H 07 LIST DB 5 DUP (7) 88 ENDS 89 18 CSEG SEGMENT 11 START: 12 MOU AX,DATA MOU DS AX 13 14 15 MOU AX, 05H MOU CX, 10 16 17 LOP1: 18 INC AX LOOP LOP1 19 20 21 MOU AH,4CH; return the control to…
14--17) Given the unusual circuit below constructed of full and half adders, determine the 5 bit output of the circuit for each of the given 2 bit values for A and B. A, B, Ao Bo НА FA НА FA 14) A = 10 B = 11 16) A = 01 B = 10 15) A = 11 B = 10 17) A = 10 B = 01
A signal with 256 symbols is transmitted by 10 symbol per second. a) What is the information rate R? b) Can the output be transmitted without error over AWGN channel with B- 10 KHz and SNR 100 c) Find the SNR required for error-free transmission for part (b) d) Find the B required for AWGN channel for error-free transmission if SNR 100
A 4-to-1 multiplexer is defined by the following symbol and truth table. f Si So S1 So 0 0 0 1 Wo Wo W1 W1 1 W2 W2 1 1 W3 W3 A logic circuit is implemented as below. The logic function f is the function of x1 and x0. Write the function f expression. Xo X1 So Wo f 1 W1 W2 W3 1