Example 4 For the transverse interior frame (Frame C) of the flat plate floor with edge beams shown in Figure, by using the Direct Design Method, find: 1) Longitudinal distribution of total static moment at factored loads. 2) Lateral distribution of moment at interior panel (column and middle strip moments atnegative and positive moments). 3) Lateral distribution of moment at exterior panel (column and middle strip moments atnegative and positive moments). Plat 5000-5000 5000 -Frame C لا بوجود deen 0009 0009 Slab thickness = 180 mm, d = 150 mm q₁ = 16.0 kN/m² All edge beams = 250x 500 mm All columns = 500x 500 mm 6000

Example 4 For the transverse interior frame (Frame C) of the flat plate floor with edge beams shown in Figure, by using the Direct Design Method, find: 1) Longitudinal distribution of total static moment at factored loads. 2) Lateral distribution of moment at interior panel (column and middle strip moments atnegative and positive moments). 3) Lateral distribution of moment at exterior panel (column and middle strip moments atnegative and positive moments). Plat 5000-5000 5000 -Frame C لا بوجود deen 0009 0009 Slab thickness = 180 mm, d = 150 mm q₁ = 16.0 kN/m² All edge beams = 250x 500 mm All columns = 500x 500 mm 6000

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter2: Concepts In Structural Steel Design

Section: Chapter Questions

Problem 2.3P: A beam is part of the framing system for the floor of an office building. The floor is subjected to...

See similar textbooks

Similar questions

For the beam shown: (a) determine the distance a for which the maximum positive and negative bending moments in the beam are equal; and (b) draw the corresponding shear and bending moment diagrams for the beam.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
The frame shown in Figure P4.7-8 is unbraced, and bending is about the x-axis of the members. All beams areW1835, and all columns areW1054. a. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. c. If Fy=50 ksi, is the stiffness reduction factor applicable to these columns?
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.