Example 2: A flow of water from a closed reservoir with interior pressure of 50 kPa to a pipe of different diameters shown in figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the .energy and hydraulic grade lines 50 kPa water 10 m D1-300mm D2-200mm D3-100mm D4-50mm (nozzel) 2m

Example 2: A flow of water from a closed reservoir with interior pressure of 50 kPa to a pipe of different diameters shown in figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the .energy and hydraulic grade lines 50 kPa water 10 m D1-300mm D2-200mm D3-100mm D4-50mm (nozzel) 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil (SG=0.80) flows through aventuri meter as shown,a. Calculate the flowrate.b. Calculate thereading ‘‘h’’ shownby the differentialmanometer fittedto the pipelinewhich is filled with mercury of specificgravity 13.6.c. How will the flow rate change if the liquidflowing through the pipeline is replacedwith water.
Exercise#3: The figure shows a system. The system is conservative energy between the two valves CV, and CV2. The differential pressure element at point 1 shows a reading for flow rate. This flow rate is equivalent to AP = 3 mmH20 with k factor of orifice equals 20 m² (used as dimension geometry for the pipe). Another turbine flow meter at point 4 shows a reading for flow rate equals 2.7. Based on the reading of the first flow meter, is the turbine flow meter give the correct reading or not? You can utilize the following given information: diameters at point1&2 are D, = D2 = 0.2 m, Dz = D4 = 2 D2, Q1= 3Q2, P4 = P3 – 200000 Pa ,p = 750 Total heads(or energy)of Bernoulli equation at point 1=Total heads(or energy)of Bernoulli equation at point 2+4m, and point2 point1 Total heads(or energy) of Bernoulli equation at point 3=Total heads(or energy) of Bernoulli equation at point 4+10m. CV, 8 Closed DP · Flow meter h tank Turbine Flowmeter CV2 voint4 point3
Oil of specific gravity 0.802 and kinematic viscosity 0.000186 m /s flows from tank A to tank B through 305 m of new pipe at the rate of 0.089 m3/s. The available head is 0.161 m. What size pipe should be used?
In a 20 cm wide rectangular flume, how much time it takes to discharge 1 liter of water? The water is moving at a 1 cm/sec velocity and the flow is 16 cm deep. O 3 sec O 6 sec O 1 sec O 11 sec
Question 4 Pipe network is given bellow (Figure 2). All pipes are 1 km long, 500 mm in diameter and Hazen-Williams Coefficient of 100.
Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the energy and hydraulic grade lines. water 10m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel)
For the setup shown in the figure :
The following data refers to centrifugal pump for pumping water. Static suction head = 5 m; Length of suction pipe = 10 m Static delivery head = 20 m Delivery pipe length = 30 m Discharge = 1500 LPM Perform complete design of pump showing suitable layout.
PLEASE HELP ME ANSWER THIS ASAP. NOTE: COMPLETE SOLUTION WITH PROPER FIGURES. 3 DECIMAL PLACES
can I please get help with part a
Be fast and quick and correct.
2.2 m/min The figure represents a simplified pipe 305 mm Infiow 1000 m 25 m /min network. Flows for the area have been disaggregated to the nodes, and a major fire flow has been added at node G. 25+ m/min The water enters the system at node A. 250 mm a.5 m/min 1100 m 8 200 mm 500 m Pipe diameters and lengths are shown on the 2.0 figure. 200 mm E 500 m 1.5 m /min Find the flow rate of water in each pipe using the Hazen-Williams equation with Crw F = 100. Carry out calculations until the 305 mm 1100 m G corrections are less then 0.2 m/min. 2.3m/min 14 m/min 305 mm 305 mm 1250 m w 0001 405 mm 1250 m 355 mm 355 w 009 w 00 ww 002 C w 00