trapezoidal flume of most efficient proportion has a base of 1.5 m. Its full discharge is 3 m^3/s, If the same material is used for a most efficient rectangular section, Compute the decrease in the discharge.   Choices: A. 0.44 m3/s B. 0:54 m3/s

Q: Compute the discharges for the pipes of the network shown below. Use the Hardy Cross method. Only…

A: Since the flow which are to be assumed are given, continuity is to be checked, that is  Flow into a…

Q: Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is…

A:

Q: A = 1.94.hmax = 0.559.R = 206 1. Filling the tank (30%) a) If the tap on the output pipe is closed…

A: A = 1.94hmax = 0.559R = 206FINDa) If the tap on the output pipe is closed (i.e. R = ∞) determine how…

Q: Question 20 There are three pipes and each has different friction or roughness factors below: Saint…

A:

Q: Stoke's Viscosity - GLYCERIN Temperature = 17 C Fluid: Sp. Gravity of fluid G = Compute density of…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: 3. Oil with sg = 0.86 is being pumped from a reservoir as shown. The pressure at point 1 to point 2…

A:

Q: Q4. B) Plotting the Energy Gradient Line (EGL) or Total Energy Line(TEL) and Hydraulic Grade Line…

A: Given, V1 = 36 ft/s  Hm = 0.25 ft

Q: Determine the discharge in liters/s of a new 1.0 m diameter cast iron pipe if the friction loss is…

A: Diameter, D =  1m Friction loss = 10 kPa Length, L = 100 m Specific gravity, S = 0.912 kinematic…

Q: A horizontal Venturi flow meter consists of a converging-diverging conduit as indicated in the…

A: The volume flow rate Q of a fluid is defined as the flow rate of fluid through a given…

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. tv low in a water pipc joint shown in the…

A:

Q: 1-m diameter new cast iron pipe is 845 m long and has a head loss of 1.11 m. 1. Find the discharge…

A:

Q: -Q.17 MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

A:

Q: Water is pumped from the large tank shown in the figure below. The head loss is known to be equal to…

A:

Q: Three reservoirs are connected.by a pipe system as shown in the a) figure and all the length and…

A: lets us take Q  is the total discharge in the pipe given  f=0.02L1=800mD1=0.3mL2=1000mD2=0.2Z1=60m…

Q: In the pipe system shown below, use Mannings Formula, n = 0.011. Determine the discharge flowing out…

A: Use Mannings Formula, n = 0.011. Reservoir A: Length, L1 = 1200 m Pipe diameter, D1 = 0.3 m…

Q: The pressure in the outlet pipe from the reservoir is 61.3 kPa abs and h =15 m. Because of the…

A:

Q: Oil (p = 888 kg/m³, µ = 0.8 kg/m.s) is to be transported in a smooth pipe having d' meter D = 5 cm…

A: Find.flow rate Qa) the pipe was horizontalb) the pipe was inclined upward by 15 degreec) The pipe…

Q: a. Find an expression for V₂. b. Find the initial time that V₂ first is zero. c. Find the mean…

A:

Q: Determine the flow rate in all pipes

A: Given: f = 0.032, Elevation difference = 13m

Q: The volumetric flow through the pump in the figure is Q = 0.014 m3 / s. The fluid being pumped is…

A:

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.