Determine the flow rate in all pipes. A pipe system shown below is connecting two reservoirs whose difference in water surface elevation is 13m.Assuming f = 0.032 for all pipes, determine the flow rate in pipe 3 (in m³/s).O 0.259O 0.094O 0.353O 0.447O 0.612Pipe 1320 m600 mmQ1Pipe 2640 m300 mmQ3 Q2Pipe 3640 m450 mmQ4Pipe 41300 m600 mm13 m

Given: f = 0.032, Elevation difference = 13m

Answered: Determine the flow rate in all pipes

Engineering

Civil Engineering

Determine the flow rate in all pipes

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 4 Determine the size of the control valve required to control the flow rate of water. The maximum flow rate is 850 gal/min, and the available pressure drop across the valve is 50 psi. Allow a safety factor of at least 30%.
Determine a. Velocity at the pipe with 8 in. diameter in ft/s. b. Pressure at point D in psi c. Flow rate in cfs d. Velocity at the pipe with 18 in. diameter in ft/s
pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
Q2- For the network shown below, compute the corrected flow rates in all pipes after one correction step (after one AQ). 150L/s B Given data: Pipe ID Length(m) Diameter(mm) AB 200 250 100L/s AC 150 200 A 50L/s BC 250 250 fAR = fac = fBc_=f= 0.016 QAB = 50 L/s
A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 80 (Hazen-Williams) Pipe 2 n = 0.015 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 1 in meters.
A differential gauge was attached to a venturi meter. The deflection of mercury is 14.3 inches. Assume no headloss. Point B is located at the 6 inches diameter pipe. Point A is located at the 12 inches pipe. Determine the flow rate in ft^3/s. 6 indves 12 inches 143 in
Determine the energy loss due to a sudden enlargement from a standard DN 25 Schedule 80 steel pipe to a DN 90 mm Schedule 80 steel pipe when the rate of flow is 3 x 10-3 m³/s.
i)Calculate the flow rate through the system.
A pipe handles a flow rate of 35 gpm. Find the minimum inside diameter that will provide an average fluid velocity not the exceed 20 ft/s.
Water flows through a one-inch diameter pipe at a velocity of 14.4 ft/s. The pipe divides into two 3/4-pipes. Find the flow rate in the two 3/4-inch pipes.
A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of 10”. What is the velocity at each section? A. Section 1: 5.89 ft/sec Section 2: 9.2 ft/sec B. Section 1: 8.9 ft/sec Section 2: 6.0 ft/sec C. Section 1: 9.9 ft/sec Section 2: 9.9 ft/sec D. Section 1: 4.89 ft/sec Section 2: 6.58 ft/sec
Compute the head loss in a 5 inches pipe if it is necessary to maintain a pressure of 36.5 psi at a point upstream and 7 ft below where the pipe discharges water into the atmosphere at the rate of 1.963 cfs. Show the diagram.