Oil (SG=0.80) flows through a venturi meter as shown, a. Calculate the flow rate. b. Calculate the reading ‘‘h’’ shown by the differential manometer fitted to the pipeline which is filled with mercury of specific gravity 13.6. c. How will the flow rate change if the liquid flowing through the pipeline is replaced with water

Q: Situation 1 Given spot levels determine the total amount of trucks with capacity of 20 cubic meters…

A:

Q: Q4) Oil of viscosity 0.1 N.S/m² is to flow through an inclined pipe by gravity. The pipe diameter is…

A:

Q: In a given setup as defined by the figure below, determine the rate of change in terms of h(t) given…

A:

Q: QI: An oil of S= 0. 8 is flowing through a venture meter having a diameter of (200- (0.5"your code…

A: To find coefficient of discharge

Q: Problem 4. (15pts) An unknow fluid has a specific gravity of 1.25 and viscosity of 5x10-³Ns/m².…

A: The objective of the question is to determine the kinematic viscosity of an unknown fluid given its…

Q: lly developed flow is assumed if the coefficient of variation for velocity measurement in the…

A: A statistical measure of the relative dispersion of data points in a data series around the mean is…

Q: A Cole pitometer is set with its orifices at the center of a 40cm pipe. For three different rates of…

A: We know that ; Discharge = Area * Velocity Q = A * V A = π4(d)2 =π4(0.4)2 = 0.126 m2 V = Velocity V…

Q: Transient Orifice Flow: Instructions Properly label the iterations. Take note of the tolerance value…

A: The flow of a fluid of a fluid is transient or unsteady if its flow  parameters [i.e. velocity and…

Q: Example For the branching system shown in Fig. 11.14, calculate the discharge each pipe. Take f =…

A: Determine the discharge in each pipe.

Q: Tests a 14.62-in-diameter centrifugal water pump at 2134 r/min yield the following data: Q, ft’/s 4…

A: To determine the specific speed we have to first determine the best efficiency point. For the best…

Q: In a test to determine the the discharge coefficient of a 50-mm by 12.5-mm Venturimeter the total…

A:

Q: An orifice meter is to be calibrated for the measurement of the flow rate of a stream of liquid…

A: Orifice meter: The orifice meter is also known as pipe orifice and orifice plate. The orifice meter…

Q: 2 In Figure below, sensor A reads 1.75 kPa (gage). All fluids are at 12°C. Determine the elevations…

A:

Q: 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines…

A:

Q: Moving to another question will save this response. Question 47 A pipe has a length of 462 m., and a…

A:

Q: The Reynolds number for the current in a pipe is 10°. If the relative roughness is 2.103, using the…

A: Reynolds number, Re=100.Relative roughness = 2.103It is asked to determine the roughness coefficient…

Q: 5. An illegal connection was observed on a 300 mm diameter horizontal pipe. Upstream from the…

A: please look into the detailed solution provided below.

Q: The theoretical discharge "Qt" can be computed by multiplying the actual value by the coefficient of…

A: Incorrect

Q: A 90-Pa capacity manometer has a reading error of + 0.421 mm. Determine the ratio of d/D so that the…

A:

Q: Problem 3: for the following manometer drawn bela Note: Not drawn to scale 30cm

A:

Q: H=81.137 O H=91.137 O H=71.137 C H=61.137 Exz- If the lowrate between two tanks is (o.s m/s), And…

A: To Determine Head loss, H

Q: An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1. 6m. It is…

A: When we rotate the cylinder a paraboloid of depth z is formedand the water will be spilled , Spilled…

Q: Q.4 (b) Recommend the low cost flow meter used in industries for measuring flow that provides…

A: - Venturimeter is a apparatus or device for measuring the speed and flow rate or the fluid discharge…

Q: 1. In Figure below, sensor A reads 3.5 kPa (gage). All fluids are at 15°CC. Determine the elevations…

A: Pressure at A = 3.5kPa

Q: Which of the following statements about Energy Grade Line (EGL) and Hydraulic Grade Line (HGL) is…

A: different statements about energy grade line (EGL) and hydraulic grade line (HGL)need to find the…

Q: Which of the following pressure-tap arrangements will yield the lowest pressure drop reading for an…

A: Orifice pressure tap positions are defined by a number of standards. The upstream pressure tap…

Q: A reciprocating pump has a stroke of 30 cm, speed of 100 rpm, and a piston of 22-5 cm diameter. It…

A: Give data:   Stroke length = 30 cm Speed = 100 rpm piston diameter = 22.5 cm discharge, Qac=18.9…

Q: PROBLEM: The discharge of the pipe system shown is 420 liters/sec, Deter- mine the head loss from A…

A:

Q: A cylinder of cross-sectional area 2657 mm² is filled with sand of permeability 16 cm/sec, water is…

A: Given Data Permeability of soil (K) = 16 cm/sec  Time of testing (t) = 10 minute  Cross sectional…

Q: 18. Water flows through a horizontal Venturi meter having an inlet diameter of 30 cm and throat of…

A: 18. Water flows through a horizontal Venturi meter with an inlet diameter of 30 cm and throat…

Q: Glycerin flows through a system composed of pipes at a rate of 7.735 m3/s, calculate the velocity…

A: WE will use bernoulli equation.

Q: 3. In Figure below, sensor A reads 2.2 kPa (gage). All fluids are at 22°C. Determine the elevations…

A:

Q: 8 A cast iron pipe (roughness = 0.010 in) connects two reservoirs. The pipeline is 1300 ft long and…

A:

Q: An orifice meter was calibrated by the manufacturer for air at 25℃ and 1atm. It is installed in an…

A: ∆P = 4.8″H2O (inches of water) Temperature during operation = 33℃ Pressure during operation = 0.9atm

Q: The pipeline shown in the figure A. takes water from a reservoir and terminates in a nozzle having a…

A: The given figure is shown below:

Q: What is the velocity (ft/s) of oil in the pipe? What is the Reynolds number?

A: This question has been taken from fluid mechanics

Q: A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m.…

A:

Q: 3. In Figure below, sensor A reads 2.5 kPa (gage). All fluids are at 10°C. Determine the elevations…

A:

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.