Estimate the power of an electric motor driven power screwthatmoves a nut in a horizontal plane against a force of 80kN at a speed of 300 mm/min. The screw has a doublesquare thread of 6 mm pitch on a nominaldiameter of 40 mm. The coefficient of friction at screw threads is 0.15.

Estimate the power of an electric motor driven power screwthatmoves a nut in a horizontal plane against a force of 80kN at a speed of 300 mm/min. The screw has a doublesquare thread of 6 mm pitch on a nominaldiameter of 40 mm. The coefficient of friction at screw threads is 0.15.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Related questions

Q: How much torque must be applied to drive the screw with the applied load in units of newton meters?

A: Here, is lead angle, is pitch, is mean thread diameter.

Q: OA double-threaded ACME screw, with a major diameter of 40 mm and a pitch of 4 mm, is used to lift a…

A: The power screw in this application exhibits self-locking behavior due to the lead angle (3.82°)…

Q: Part B In the machine design the bed with a mass of 250 kg is moved by a lead screw which has a…

Q: Two identical 4 in. major-diameter power screws (single-thread) with modified square threads are…

A: Given:f = 0.1fc = 0.24v = 3ft/min = 36 in /minTo find:Power required to drive each screw when the…

Q: A single-threaded power screw with square threads pushes against a load of 3,736 N at a speed of 42…

A: Here, is lead angle, is pitch, is mean thread diameter.

Q: single square-thread screw has an input power of 3 kW at a speed of 1 rev/s. The screw has a…

Q: A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm…

A: The answer is given in the following step

Q: 7. A screw jack is used to lift a mass of 2.00 tonnes. The pitch of the thread is 10.0 mm with a…

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: i need the answer quickly

Q: A single-threaded power screw with square threads pushes against a load of 3,276 N at a speed of 14…

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction: A governor is a mechanism that is used to keep an engine's mean speed within set…

Q: A Machine vice has single start square threads with nominal diameter 22 mm and pitch 5 mm. Collar…

A: Given: Force applied on the handle(F)=125N, Coefficient Of Friction of Threads (ϕ)=0.15,,…

Q: A double-threaded power screw with square threads pushes against a load of 3,641 N at a speed of 15…

A: Here, is lead angle, is pitch, is mean thread diameter.

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1,

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

HW5 The tension in a pulley belt is 30 N when stationary. Calculate the tension in each side and the power transmitted when the belt is on the point of slipping on the smaller wheel, the wheel is 300 mm diameter and the coefficient of friction is 0.4. The angle of lap is 160°. The wheel speed is 1420 rev/Min.
A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 8 mm thick and 250 mm wide is used. The diameters of the motor pulley and the driven pulley are 350 mm and 1370 mm. The center distance is 1370 mm, and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress for the belt is 2.4 MPa, which allows for the factor of safety and also for the fact that a double ply belt does not have double the capacity of a single ply belt. (A double ply belt has approximately 85% the capacity of a single ply belt of the same thickness.) The belt density p =970 kg/m^3. What is the power capacity? (Answer: 39.1 kW ) -0350 -1370
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
A single-threaded power screw with square threads pushes against a load of 3,276 N at a speed of 14 mm/s. The screw has a mean thread diameter of 18 mm and a pitch of 2 mm. The frictional coefficient of the threads is 0.33, and collar friction is negligible. How much torque must be applied to drive the screw against the applied load in units of newton meters? A double frictiona
An overhang shaft carry a 900mm diameter pulley, whose center is 250mm from the center of nearest bearing. The weight of the pulley is 600N and the angle of lap is 180°.The pulley is driven by motor horizontally to right it, if the permissible tension in the belt is 2650N and the coefficient of friction between the belt and the pulley surface is 0.3, estimate the diameter of the shaft. Note, Neglect centrifugal tension and assume permissible tensile and shear stresses in the shaft as 84MPA and 68MPa respectively.
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
A pullev 615 mm in diameter transmits 40 kW at 630 rpm The arc of contact between the belt and the pulley is 140 degrees, the coefficient of friction between the belt and the pulley is 0.30, and the safe working stress of the belt is 2.0 MPa. Calculate the effective belt pull
HW6 A belt drive must transmit 10 kW of power at 3000 rev/min. The wheel is 200 mm diameter and the coefficient of friction is 0.35. The lap angle is 150°. The belt tension must not exceed 50 N. Calculate the minimum number of belts required.
A single-threaded power screw with square threads lowers a load of 3,856 N at a speed of 43 mm/s. The screw has a mean thread diameter of 16 mm and a pitch of 3 mm. The frictional coefficient of the threads is 0.32, and collar friction is negligible. How much torque must be applied to drive the screw with the applied load in units of newton meters? The efficiency of a
A square thread power screw has pitch of 4-mm with double threads. Applicable data are threadand collar coefficient of friction equal to 0.08, collar diameter of 40-mm, and a load of 6.4-kNper screw and mean diameter of 30mmDetermine:a. Torques required to rotate the screw with” and “against” the load.b. Overall efficiency.
A pulley, 610 mm. in diameter, transmits 40 kW at 500 rpm. The arc of contact between the belt and the pulley is 144 degrees, the coefficient of friction between the belt and the pulley is 0.35 and the safe working stress of the belt is 2.1 MPa. Find the width of the belt if its thickness is 6 mm.
A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 5/16 inches thick and 10 inches wide is used. The diameters of the motor pulley and the driven pulley are 14 inches and 54 inches, respectively. The center distance is 54 inches and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress of the belt is 350 psi and the belt weighs 0.035 lb/in^3. What is the horsepower capacity of the belt?