A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 8 mm thick and 250 mm wide is used. The diameters of the motor pulley and the driven pulley are 350 mm and 1370 mm. The center distance is 1370 mm, and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress for the belt is 2.4 MPa, which allows for the factor of safety and also for the fact that a double ply belt does not have double the capacity of a single ply belt. (A double ply belt has approximately 85% the capacity of a single ply belt of the same thickness.) The belt density p =970 kg/m^3. What is the power capacity? (Answer: 39.1 kW ) -0350 1370

A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 8 mm thick and 250 mm wide is used. The diameters of the motor pulley and the driven pulley are 350 mm and 1370 mm. The center distance is 1370 mm, and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress for the belt is 2.4 MPa, which allows for the factor of safety and also for the fact that a double ply belt does not have double the capacity of a single ply belt. (A double ply belt has approximately 85% the capacity of a single ply belt of the same thickness.) The belt density p =970 kg/m^3. What is the power capacity? (Answer: 39.1 kW ) -0350 1370

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: In the machine design the bed with a mass of 250 kg is moved by a lead screw which has a square…

Q: A screw jack has a thread with a pitch of 4 mm and diameter 22mm. The coefficient of friction is…

A: A screw jack withThe pitch of thread (p) = 4 mmThe diameter (d) = 22 mm The coefficient of friction…

Q: How much torque must be applied to drive the screw with the applied load in units of newton meters?

A: Here, is lead angle, is pitch, is mean thread diameter.

Q: A double-threaded power screw is used to raise a load of 5 kN. The nominal diameter is 60 mm and…

Q: (11) Find the power required to drive a power screw lifting a load of 40001b. A 2½-in double square…

Q: A conical pivot with angle of cone as 100° supports a load of 18 kN. The external radius is 2.5…

Q: on c is 0, what is th

Q: OA double-threaded ACME screw, with a major diameter of 40 mm and a pitch of 4 mm, is used to lift a…

A: The power screw in this application exhibits self-locking behavior due to the lead angle (3.82°)…

Q: Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The…

Q: You have to build a box lifter, this will be made with a square threaded power screw. The power…

Q: Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: (b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside…

A: Given: Outside diameter, D = 380 mm or 0.38 m Inside diameter, d = 270 mm or 0.27 m Pressure, P =…

Q: 3. The safe working stress of a belt is equal to the tight side tension over the product of the…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: A clutch is a device that allows two parts with a shared axis of rotation to connect and disengage…

Q: A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion…

A: Friction Clutch Friction clutch is used to transmit the power in shafts and machines which must be…

Q: A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is…

Q: In a thrust bearing, the external and the intermal diameters of the contacting surfaces are 320 mm…

Q: A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is…

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of…

A: please refer handwritten solution

Q: A screw jack has a thread with a pitch of 4 mm and diameter 22mm. The coefficient of friction is…

Q: 2. A cylinder with a nominal 2.5 inch ID, a 4.0 inch OD, and a 3.0 inch length is to be mated with a…

A: To calculate the maximum amount of torque transmission and to determine the yield condition of a…

Q: You have to build a box lifter, this will be made with a square threaded power screw. The power…

A: The objective of the question is to calculate the depth of the thread, the width of the face, the…

Q: A multi-plate clutch as in the figure below transmits power at 1500 rpm. The coefficient of friction…

A: Clutches need a way to be activated in order to cease the transmission of torque. The clutch pedal…

Q: Outer and Inner diameter of a thrust bearing are 320 mm and 200 mm respectively . Axial load is 80…

A: Given Datad0=320mmdi=200mmW=80kNP=350kN/m2

Q: A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter…

A: GIVEN DATA- m=585kg dm=20mm p=5mm Coefficient of friction =0.1 We have to find torque required to…

Q: Problem -02 Dry FrictionKnowing that a couple of magnitude 30 N m is required to start the vertical…

Q: An automobile single plate clutch consists of a pair of contacting surfaces. The inner and outer…

A: Uniform pressure theory: When the clutch and bearing mating components are fresh, the contact…

Q: Find the value of coefficient of friction if friction force is 200 N and Normal force is 780 N

Q: A single square thread power screw has a lead of 7 mm and mean diameter of 35 mm. If it Is used to…

Q: A square thread has a pitch of 3 mm and a diameter of 15 mm. The coefficient of friction is 0.2.…

A: Given:Pitch of a square thread, p=3 mmDiameter of thread, d=15 mmThe coefficient of friction,…

Q: The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12…

Q: À conical pivo of pressure is the diameters the coefficient

A: Given data:

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A fan is driven by a belt from a motor which
runs at 880 rpm. A medium double ply
leather belt 8 mm thick and 250 mm wide is
used. The diameters of the motor pulley
and the driven pulley are 350 mm and 1370
mm. The center distance is 1370 mm, and
both pulleys are made of cast iron.
Coefficient of friction of leather on cast iron
is 0.35. The allowable stress for the belt is
2.4 MPa, which allows for the factor of
safety and also for the fact that a double ply
belt does not have double the capacity of a
single ply belt. (A double ply belt has
approximately 85% the capacity of a single
ply belt of the same thickness.) The belt
density p =970 kg/m^3. What is the power
capacity? (Answer: 39.1 kW )
-0350
-1370

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Calculation

VIEW

Step 3: Conclusion

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
Please answer ASAP. I will rate helpful.
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.
Solve show solution
A single trapezoidal metric thread power screw is to raise a load of 60 kN. The screw has a mean diameter of 34 mm and a pitch of 5 mm. The coefficient of thread friction and collar friction are 0.15 and 0.11, respectively. The collar mean diameter is 90 mm and the screw turns at 150 rpm. Determine the total torque required to raise the load in N-m.
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.2. The torque to increase the load and the efficiency of the screw.3. The speed of the motor (in rpm), if it is directly coupled to the screw and it is desired that the boxes rise at a speed of 30 inches/min.