Equal torques T= 5 kip · ft are applied to the two steel bars with the cross sections shown. (Note that the cross-sectional areas of the bars are equal.) The length of each bar is 8 ft. Calculate the maximum shear stress and angle of twist for each bar. Use G= 12 × 106 psi for steel. 5 in. 10 in. 2 in. 1.0 in. (b) FIG. P3.52

Equal torques T= 5 kip · ft are applied to the two steel bars with the cross sections shown. (Note that the cross-sectional areas of the bars are equal.) The length of each bar is 8 ft. Calculate the maximum shear stress and angle of twist for each bar. Use G= 12 × 106 psi for steel. 5 in. 10 in. 2 in. 1.0 in. (b) FIG. P3.52

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.
A 3-m aluminum tube with the cross section shown carries a 200 N-m torque. Determine the following: a) the Maximum Shear Stress in the tube b) The relative angle of rotation of the ends of the tube. (For aluminum, use G = 28GPA) 100 mm 50 mm 2.4 mm 1.2 mm
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). ... 10 lb-ft 50 lb-ft 70 lb-ft |(1) 30 lb-ft A (3) B C D
3. A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross- sectional area of 150 mm x 310 mm to the median line of the cross-section. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube . If it is subjected to a torque T = 15 kN-m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa. Thickness of the tube is 10 mm and the torque T = 15 kN-m.
Assume a single 300-N force is exerted on a bicycle frame as shown in the figure. Consider the torque produced by this force about axes perpendicular to the plane of the paper and through each of the points A through E, where E is the center of mass of the frame. Rank the torques TA, TB, TC, TD, and TE from largest to smallest, noting that zero is greater than a negative quantity. If two torques are equal, note their equality in your ranking.
A solid 2.9-in.-diameter bronze [ G = 7100 ksi] shaft is 8-ft long. The allowable shear stress in the shaft is 10.2 ksi and the angle of twist must not exceed 0.034 rad. Determine the maximum horsepower P that this shaft can deliver: (a) when rotating at 182 rpm. (b) when rotating at 644 rpm.
1. A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6º. Remember to consider both the maximum shear stress and the angle of twist. MATERIAL MODULUS OF RIGIDITY MAXIMUM SHEAR STRESS TORQUE Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa
(2) The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel. | Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft D
A hollow steel shaft with an outside diameter of 41 mm and a wall thickness of 9 mm is subjected to a pure torque of T = 6300 N-m. The shear modulus of the steel is G = 87 GPa. Determine: (a) the maximum shear stress T in the shaft. (b) the magnitude of the angle of twist o in a 2.4-m length of shaft. Answers: (a) = i MPа. (b) p = i
1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 lb-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.
The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip٠in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel.