A solid 0.72-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft (1) O 2273 psi O 1549 psi O 1637 psi 1367 psi O 2118 psi 50 lb-ft B 70 lb-ft C (3) 30 lb-ft

A solid 0.72-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft (1) O 2273 psi O 1549 psi O 1637 psi 1367 psi O 2118 psi 50 lb-ft B 70 lb-ft C (3) 30 lb-ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the intemal torque diagram .
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
The shaft is fixed at ends A and B and has a positive torque T a distance of 4m from A and 8m from end B. If the angle of twist is zero and the reaction torque at A is 334N-m, what is the magnitute of applied torque T?
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 320 N-m, Tc = 371 N-m, and TD = 181 N-m. TD (3) O -208 N-m O -224 N-m O -138 N-m O -190 N-m O -265 N-m Tc (2) B TB (1) TA
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
6. I upvote! Thanks!
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi
The motor on the left provides a torque of 5500 N•m to the gear shaft shown. The motor runs machines connected to gears B, C and D requiring torques of 3000 N•m, 1500 N•m and 1000 N•m respectively. A, B, C and D are spaced 2000 mm apart and the diameter of the shaft is 75 mm. The shear modulus of the shaft material is 80x109 N/m2. Determine: Minimum diameter required (in millimeters) if the shearing stress in the shaft is limited to 100x106 N/m2 Rotation of D with respect to A Note: Draw the Free Body Diagram, Compute for all of the necessary elements, Include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
The axis ABCD receives a torque of 500Nm from the motor and transmits movement to other devices, by means of belts and pulleys connected at B and C. If it is known that the torques exerted on pulleys B and C are as shown In the figure, determine the minimum radius the shaft must have. You should consider that at point D of the motor there is a bearing that acts as a support for the shaft as at point A. The material of the shaft and its allowable shear stress are indicated in the drawing.Determine:to. Free-Body diagram.b. Shear force diagrams.c. Bending moment diagrams.d. Identification of the critical point of the axis.e. Calculation of the axis radius. tperm=80MPa
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi