If the shaft shown in Figure is m ade of one materialand is subjected to torques TI=25 kN.m and T2-60KN.m, determ ine the values of JAB, Bc and distance Lso that the angle of wist at end A is zero. Knowingthat part AB has hollow cross section wih innerradius 80 mm aad outer radhus 100 mm, and part BCS0 mm10 mmhas solid eross secetion with radius equal to 100 mm).Section aaJAB=92739815 mmJBC=157079632 mm“,a.4L=452.5 mm4D JAB-92739815 mm* ,JBC=157079632 mm4,L=542.5 mmO JAB=5796238 mm,JBC=9817477 mm , L=542.54mmd.JAB-5796238 mm" ,JBC=9817477 mm , L=452.5mm

Answered: Image /qna-images/answer/766c6452-c87c-4edf-a0bc-ad85f735001d.jpg

If the chaft shown in Figure is made of one material and is subjected to torques TI-25 kN.n and T2-60 kN.m, detem ine the values of JAn, Jac aad distance L so that the angle of wist at end A is zero. Knowing that part AB has hollow cross section wih inner radius 80 mm and outer radias 100 mm, and part BC has solid eross seetion with radius equal to 100 mm).

If the chaft shown in Figure is made of one material and is subjected to torques TI-25 kN.n and T2-60 kN.m, detem ine the values of JAn, Jac aad distance L so that the angle of wist at end A is zero. Knowing that part AB has hollow cross section wih inner radius 80 mm and outer radias 100 mm, and part BC has solid eross seetion with radius equal to 100 mm).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 263 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 190 mm in diameter. If the torque that can be applied is 9494 Nm without exceeding a shearing stress of 46.89 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
only HANDWRITTEN answer needed ( NOT TYPED)
A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m. Determine the resulting torque maximum and minimum shear stress.
A hollow aluminum shaft with an outside diameter of 76 mm and a wall thickness of 5 mm has an allowable shear stress of 49 MPa. Determine the maximum torque T that may be applied to the shaft. O 2.47 kN-m O 1.94 kN-m O 2.11 kN-m O 1.33 kN-m O 1.82 kN-m
2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as shown in Figure Q2. Knowing that the entire shaft is made of aluminium for which G = 27GPa, a. b. Determine the maximum shear stress and its location. Angle of twist at end D. ASSIGNMENT 2 030 Section p-p d D P Р Ø40 200 00 Section q-q 9 9 200 016 1500 Nm All dimensions in mm Section r-r 500 030 SEMU2113 500 Nm
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 262 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 200 mm in diameter. If the torque that can be applied is 7381 Nm without exceeding a shearing stress of 44.07 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
2
A CIRCULAR STEEL SHAFT (G= 80 G Pa ) Is COADED Bu Two TORQUES. AT Points A Awo C As SHOWN. FiNo: THE ANGLE OF TuIST OF POINT C RELATIVE To Poiut A Ø% in RAMIANS
Six 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel and six 20 mm diameter bolt in the inner bolt circle of 260 mm diameterare aluminum. What is the torque capacity of the coupling? Assume thatthe allowable shearing stress for the steel bolts is 40 Mpa and aluminumbolts of 30 Mpa. The Shear modulus of elasticity of aluminum and steel are28 Gpa and 84 Gpa, respectively.
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an outside diameter of 0.51 in. and an allowable shear stress of 4500 psi. Segment (2) is a solid aluminum shaft with an outside diameter of 0.41 in. and an allowable shear stress of 6000 psi. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in lb-in rounded to the nearest tenths.
Illustrate and completely solve the problem! Write legibly or type written the solutions. The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4 x 103 ksi and G brass at 5.2 x 103 ksi.
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa