A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc= i (2) Te (3) Tp lb-ft D

A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc= i (2) Te (3) Tp lb-ft D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

A: To determine:The magnitude of maximum shear stress in the shaft()

Q: The solid shaft is fixed at A and free at D. It is subjected to three concentrated torques at B, C…

Q: 2. The circular shaft has fixed supports at both ends, points A and D. Determine the torque that…

Q: diameter solid steel cylinder in which a 7 mm diameter hole has been drilled from end B up to point…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 lb, a horizontal shear…

A: Solution:

Q: Hi, I need help with this question.

Q: A shaft consisting of an aluminum segment and a steel segment is acted upon by two torques. The…

A: The diameter of the aluminum section is The diameter of steel section is The shear modulus of…

Q: Figure 2 shows a solid shaft consisting of two prismatic circular parts in equilibrium under the…

Q: The 70-mm-diameter solid shaft shown is subjected to torques of 600 N·m and 1400 N·m at points B and…

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: 2. A shaft is designed to carry torque as shown below. The shaft consists of a steel rod which is…

Q: 2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as…

Q: Problem1: The entire composite shaft shown in the following figure is manufactured using steel with…

A: GivenG=80GPatorque =Tτa=75MPa

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions
shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc
that can be applied to the shaft.
(1)
Answer: Tc i
B
(2)
b
Tc
(3)
Tp
lb-ft
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce to the given data

VIEW

Step 2: Calculate for the torque in the each segment

VIEW

Step 3: Calculate for the shear stress in the each segment

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 15 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and freely in bearings at points A and E. The shaft is driven by a gear at C, which applies a torque T₂ = 625 N_m in the direction shown in the figure. Gears at B and D are driven by the shaft and have resisting torques T₁ and T3, acting in the opposite direction to the torque T2. We know T₁ = 400 N.m, but T3 is not explicitly given in the problem. Segments BC and CD have lengths LBC= 550 mm and LCD = 400 mm, respectively, and the shear modulus G = 80 GPa. Determine the maximum shear stress in each segment of the shaft and the angle of twist between gears B and D. pôrôć -LBC LCD T3 E
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
A composite shaft shown, composed of a steel (G = 77 GPa) core inside an aluminum (G = 25 GPa) jacket, carries a torque, T = 10 kN-m. The shaft is designed such that the aluminum jacket will fail first upon the application of the torque.What must be the minimum shear strength of steel such that the aluminum jacket will fail first? (Please explain)
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi
A solid circular steel shaft having an outside diameter of 2.25 in. is subjected to a pure torque of T = 9060 Ib-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. O 3.31 ksi O 5.15 ksi O 4.05 ksi 3.82 ksi O 2.53 ksi
Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor machine tools connected to gears F and G. Assuming that, 10 kW is taken off at gear F and 20 k taken off at gear G, knowing that allowable torsional shear stress is equal to (65 plus last digit of student ID) MPa. Design the smallest permissible diameter of shaft AB. Figure 1 150 mm 225 mm 905 mm 150 mm 60 mm 100 mm D. 60 mm B.
Part A The solid shaft cross-sections shown are subjected to the externally applied torques shown. Compare the corresponding shear stresses developed in each shaft at point P. P P 2 T Rank the solid shafts from the largest shear stress at P to the smallest shear stress at P. (For example, 4> 3 = 1 > 2). 0.5 T
The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum shear stress in the shaft and the rotation of end gear A with respect to fixed support E 40 Nm 280 Nm 05 m 150 N m 100 m 04 m (a)
A solid steel shaft of circular cross-section has diameter 50 mm, length 1,028 mm and shear modulus 79.3 GPa. If the allowable shear stress is 36 MPa and the allowable angle of twist is 1.9°, determine the maximum permissible torque. Give your answer in Nm to 1 decimal place.
A 1.50-in.-diameter solid shaft is subjected to an axial force of P = 1700 lb, a horizontal shear force of V = 180 lb, and a concentrated torque of T = 2200 lb-in., acting in the directions shown. Assume L = 7.5 in. Section properties for the shaft are A = 1.7671 in.2, J = 0.497 in.4, Iy = Iz = 0.2485 in.4, and Q = 0.2812 in.3. Determine the normal and shear stresses at point K, and show these stresses on a stress element.