A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 175 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 54 in., b = 78 in., and c = 24 in. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque Tc that can be applied to the shaft. y (1) a Answer: Tc= i B (2) Tc (3) Tp lb-ft D

A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 175 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 54 in., b = 78 in., and c = 24 in. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque Tc that can be applied to the shaft. y (1) a Answer: Tc= i B (2) Tc (3) Tp lb-ft D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 150 mm and a wall thickness of 10 mm. The shaft is subjected to torques TB = 42 kN-m and TC = 18 kN-m, which act in the directions shown in Figure. Determine the maximum shear stress magnitude in Segment (2). J1= 54019686 mm4J23D 21551281 mm4 TB Tc (2) O 88.8 MPa 62.3 MPa O 44.4 MPa 124 6 MPa
A hollow steel shaft with an outside diameter of 62 mm and a wall thickness of 6 mm is subjected to a pure torque of T = 7300 N-m. The shear modulus of the steel is G = 73 GPa. Determine: (a) the maximum shear stress T in the shaft. (b) the magnitude of the angle of twist p in a 2-m length of shaft. Answers: (a) T = i MPа. (b) Φ
2. A shaft is designed to carry torque as shown below. The shaft consists of a steel rod which is fixed against rotation at both ends. In addition, the left half of the rod is well bonded to an aluminum sleeve. The assembly is loaded by a torque of 2000 N-m as shown. - The steel rod has shear modulus G = 80 GPa and radius r= 1.5 cm (hence polar moment of inertia Ip = 7.95 x 108 m². The aluminum sleeve has shear modulus G = 26 GPa, outer radius 2.6 cm and inner radius 1.5 cm (hence polar moment of inertia I, = 7.95 x 108 m²). 2000 N sleeve -0.57 rod a. Calculate the total reaction torques at the two walls (points A and C). b. Calculate the maximum shear stresses in the steel rod and the aluminum sleeve. c. Calculate the angle of twist at point B.
2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as shown in Figure Q2. Knowing that the entire shaft is made of aluminium for which G=27GPa, a. Determine the maximum shear stress and its location. Angle of twist at end D. b. EMU2113 Ø40 Ø30 Section p-p р A р 200 Section q-q 016 1500 Nm q 200 All dimensions in mm Figure Q2 Section r-r 500 Ø30 D 500 Nm
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
A compound steel (G= 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm- diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to Pcs 4.6°. Assume ₁-0.6 m and £₂-1.0 m. Determine the magnitude of the largest torque Te that may be applied at C. Express your answer in N-m rounded to three significant digits. L₁ (1) B (2) L2 Tc C X
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment. Answers: T1 = i T2 = i (1) (2) MPa. MPa.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.46 GPa. For the steel segment BC, the diameter is 50 mm and G = 84.51 GPa. Given that a = 2.2 m and b = 1.35 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.01 MPa in the bronze and 83.59 MPa in the steel. Round off the final answer to two decimal places.
2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as shown in Figure Q2. Knowing that the entire shaft is made of aluminium for which G = 27GPa, a. b. Determine the maximum shear stress and its location. Angle of twist at end D. ASSIGNMENT 2 030 Section p-p d D P Р Ø40 200 00 Section q-q 9 9 200 016 1500 Nm All dimensions in mm Section r-r 500 030 SEMU2113 500 Nm
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and freely in bearings at points A and E. The shaft is driven by a gear at C, which applies a torque T₂ = 625 N_m in the direction shown in the figure. Gears at B and D are driven by the shaft and have resisting torques T₁ and T3, acting in the opposite direction to the torque T2. We know T₁ = 400 N.m, but T3 is not explicitly given in the problem. Segments BC and CD have lengths LBC= 550 mm and LCD = 400 mm, respectively, and the shear modulus G = 80 GPa. Determine the maximum shear stress in each segment of the shaft and the angle of twist between gears B and D. pôrôć -LBC LCD T3 E
A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc i B (2) b Tc (3) Tp lb-ft D