Draw the stratigraphic correlation between the following three outcrops. (A), (B).(C) and (D).Vertical scale 1cm:10m.Section (A)unitThick (m)Lithologic description512Fine grained sanstone423324235Dolomitic LSTLSTshale152siltstoneSection (B)unitThick (m)45316224157Section (C)Section (D)unitThick (m)52410334212127unitThick (m)62510434310212127Lithologic descriptionDolomitic LSTLSTshalesiltstoneLithologic descriptionFine grained sanstonDolomitic LSTLSTshalesiltstoneLithologic descriptiongrained sanstoneDolomitic LSTLSTEvaporateshalesiltstone

Approach to solving the question: through illustrating stratigraphic column. Detailed…

Answered: Draw the stratigraphic correlation…

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter13: Stone

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

Provide complete answer with explanation.solution must be neat and easy to understand(preferrably handwritten) will give like if you follow instructions
The contour map in Figure 1 depicts porosity variation within a sandstone reservoir. The lines connect points of equal porosity. If reservoir is 10 miles long, 3 miles wide, 100 ft thick and Table 1 depicts the area and thickness. Analyze: a) An average porosity. b) the most possible average pore volume in barrel
To the right is an "exploded" block diagram displaying an emergent anticline penetrated by four vertical wells. The area consists of Paleozoic and Mesozoic sequences of rocks separated by an unconformity. CRETACEOU unit X Below is a map of well locations from the block diagram and depths to the stratigraphic top of Jurassic unit Y. Tape a piece of tracing paper over the map and using a pencil, neatly draw and label structure contours on the top of this unit. Choose an appropriate contour interval. JURASS IC unit Y UNLUNPONM A ENN DEV. CAM. -140' -40' 80' 150' 205' 25' -60' 210 100 200' 40' -25' 210 50' 30' 220' •80' 70 190' -130' -30' '-160' 5' -115' -160' -110' -210'
Define the types of rock.
2 = (0,0,0) 1. Determine the value site with dimensions of 5 m x 3 m according to the following figure. 1 Note: ΔΕ, Hint: at each point according to the notes that are under the foundation Coordinat system dalam (x, y, z) Point A is located at coordinates (2.5, 1.5, -10) Point B is located at coordinates (2, 1,-5) Point C is located at coordinates (5, 0, -10) Point D is located at coordinates (6, 1,-5) The load value (Q) on the footing is 100 kN • Use Fadum charts 5m 3 3 m 4 • The value of q (surface tension) for each point is the same, use the formula q = Q/A, the value of Q is the foundation load and A is the area of the foundation footprint
What other term is synonymous with texture in a rock?a. Specific gravity c. Streakb. Grain size d. Porosity
What will be the shearing resistance of a sample of clay in an unconfined compression test, falls under a load of 150 N? Take change of cross-section Af=2181.7 mm2.
For studying rock porosity change affecting by the pressure, use Newman correlation to calculate the pore volume (isothermal) compressibility, cf, for sandstones as below (Eqn. 2.2 - which is attached). I have also attached my results for part a. I need help with part B. It is using the formula: c = -1/v * dV/dp where v = volume, c = compressibility values calculated in part a, and p is pressure. I am mostly confused on how to compute the change in volume. (a) Calculate cf for 5 different phi (porosity) = 0.02, 0.05, 0.1, 0.15, 0.2 I have already completed this portion and it is attached with the answers needed for part b highlighted in yellow in the uploaded figure. (b) Estimate dV/V for these five cases of phi (porosity), if initial reservoir is 3250 psia and the current reservoir pressure is 1500 psia.
Complete cross section for the red line on text Michigan Basin map. Kehew 2006, Page 185 Canadian Shield Lake Superior Precambrian Cambrian Ordovician Lake Huron Silurian Devonian Mississippian Pennsylvanian Jurassic Michigan Basin Howell Anticline Lake WISCONSIN Chatham Sag Michigan Bowling Green Fault - MICHIGAN INDIANA OHIC 60 mi Kankakee Arch 100 km Shale Source Rocks Permeable Reservoir Rocks: Sandstone 4800 M Limestone Marine Sediments Dolomite O 2006 Pearson Education, Inc. Lake
According to the Geo technical report what is the depth of top soil layer in Borehole BH2? O 150mm O 100mm 200mm O 400mm
a) How could two/three new or existing fractures simultaneously form (under perfect ideal conditions) and/or move under these conditions. (fig B) b) What are the resolved normal and shear stresses on the faults and what angle do they make to o1 (draw sketch). c) mark faults on cylinder of rock (left below) orientations where fractures cannot either form or slip. 01 Os 30 Rock 20- 10- - Plane of weakness MPa 10 40 Figure 5
A pre-engineering baseline was run down a very steep hill. Rather than measure horizontally downhill with the steel tape, the surveyor measures the vertical angle with a theodolite and the slope distance with steel tape. The vertical angle is -21° 26’ turned to a point on a plumbed range pole that is 4.88 ft above the ground. The slope distance from the theodolite to the point on the range pole is 148.61 ft. The theodolite’s optical center is 4.66 ft above the upper baseline station at 110 + 71.25. What is the stationing chainage of the lower station? Recall 110+71.25 just means it is 11,071.25 feet from the origin point of the project. The plus sign is just a separator between the hundreds of feet and the tens of feet

SEE MORE QUESTIONS

Recommended textbooks for you

Construction Materials, Methods and Techniques (M…

Civil Engineering

ISBN:

9781305086272

Author:

William P. Spence, Eva Kultermann

Publisher:

Cengage Learning