Please solve and answer the problem correctly please. Thank you! Draw the schematic of the gearbox system used in helicopter using Helicopter Gear Reduction (youtube.com) and show typesof gears at each stage, transmission ratio and number of teeth. No need for solid modeling, simple schematic (even 2D) usinga pen and paper is enough.

The image you sent me appears to be a screenshot of a computer program related to gearboxes. The…

Answered: Draw the schematic of the gearbox…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hello, I hope you can help me. I'm trying to create a device that has a spinning axle and I need to change the rotational force to be perpendicular to the axle. I know there are gears that can fit together have teeth, like the attached picture. I know there are other types of mechanisms, and some are more creative. But I also need for the solution to be low friction. What are 2 low friction methods of changing the directional rotation of a power axle 90 degrees? The entire creation is small, probably 12" x 12" Thanks for your help.
a) Figure Q3a shows a stage 1 to stage 2 compound gear train through from Gears A, B, C to D. If the input shaft rotates at 1300 revolutions per minute (rpm), calculate the angular velocity (w) in rad/s at the output shaft of the compound gear train. See below for the number of teeth for Gears A, B, C & D. [10 marks] Gear A: 44 Teeth Gear B: 96 Teeth Gear C: 60 Teeth Gear D: 140 Teeth Gear B- -Stage 2 Gear A- Input shaft- Stage 1- Gear C- -Gear D -Intermediate shaft -Output shaft Figure Q3a b) A motor with a power rating of 3600 Watts is coupled to the input shaft of the pinion (or driver) Gear A as shown in Figure Q3a. Calculate the torque at the input shaft and at the output shaft. Assume no losses and 100% efficiency. [5 marks] c) Draw a typical indicator diagram of pressure versus volume (p-v) to illustrate the actual Otto cycle for a four-stroke reciprocating internal combustion [RIC] engine. Clearly label each part of the p-v indicator diagram and clearly indicate when the piston…
write why high 1.700 contact stifness and contact ratio is important ?? also about the importance of high mesh and fatiuge faluires ..... if the stifness ratio and conatct ratio
Please solve and answer the problem correctly please. Thank you!
For my assigment, I was asked to design a electric motorbike that has a peformance equal to Honda CBR1000 Fireblade which has a petrol engine. A part of the the assignment is to calculate " An estimate of maximum Power your new motor will need to generate to match the Honda’s performance." I can make the assumption, apart from changing the motor, everything else is going to stay the same so the fairing,the rider and etc they're gonna be the same for the two bikes. So can you please tell me how I can calculate that which information would I need ?
480 ft-lbf First Gear (2.66) Final Drive (3.42) Axle Torque Thrust Force Figure 2 - Corvette Z06 and its transmission schematic. You start by measuring the 60-0 mph braking performance, which is accomplished along 30.56 m. The test weight (including the driver) was found to be 1510.5 kgf. 1) "Fuel is spent to make the vehicle go uphill, as you are aware. However, the fuel will not be restored if the vehicle is brought back from the hilltop to the initial elevation level."ANALYSE this statement under the laws of Thermodynamics.
For the manipulator shown in the figure below, answer the following; P 1) How many joints does this manipulator have, and what types? 2) What are the measurements needed to analyse the mechanism? 3) Assign appropriate frames for D.-H. analysis from frame {0} to frame {P}? (redraw the manipulator on the answer book or do it on the questions sheet) 4) Is this a 2D problem or a 3D problem, and explain why?
An epicyclic gear box is designed as below Input C C B D B A to = 20 tв = 140 Output The input D rotates at 200 rpm clockwise viewed from the left with a torque of 40 Nm. The efficiency is 75%. Calculate the following a) The gear box ratio b) The output speed and it's direction c) The power output d) The holding torque
Please help me answer this, I just need the interpretation of this or how to draw this given the instructions. Pleasee, show me how you draw this, thank you in advance!
Summarise the main principles of designing a part or component using a Computer Aided Design (CAD) tool such as Solidworks, i.e. how do you go about creating the CAD geometry? 2. (а) (b) Briefly explain what is meant by dimensions and relations in Solidworks, why these are used and how to control and manage these. (c) Briefly discuss aspects of good practice for the development of the CAD design file within the Solidworks software. (d) You have to re-design a low cost stackable foot stool. Suggest how the design could be developed to reduce costs.
Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550 lb-ft of torque at 5000 rpm, and the manual transmission is in 3rd gear with a gear ratio of 1.5:1. Calculate the transmission output speed and output torque. Transmission output speed %3D Transmission output torque =
Help me to mach the number to the proper terminology

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Draw the schematic of the gearbox system used in helicopter using Helicopter Gear Reduction (youtube.com) and show types of gears at each stage, transmission ratio and number of teeth. No need for solid modeling, simple schematic (even 2D) using a pen and paper is enough.